Antique Tractors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Old Iron and Tractor Community > Antique Steel Wheel Tractors - Old Iron Lugs and Cleats
Forgot Password? Join Us!

Notices

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats Photos and information about antique steel wheeled farm tractors. This is where to find the heaviest of Old Iron tractors.

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats

Heider Cone Replacement


this thread has 22 replies and has been viewed 4596 times

Reply
 
Thread Tools Display Modes
  #1  
Old 01-29-2011, 03:32:41 PM
FArmstrong FArmstrong is offline
Registered-III
 
Join Date: Feb 2007
Location: Valparaiso, Indiana
Posts: 212
Thanks: 643
Thanked 306 Times in 87 Posts
Default Heider Cone Replacement

Began getting access to the cone pulley on the Heider. Not sure how much of the pulley needs to come off the shaft.
Fred
Attached Thumbnails
Click image for larger version

Name:	100_0006.jpg
Views:	311
Size:	91.6 KB
ID:	99082   Click image for larger version

Name:	100_0008.jpg
Views:	313
Size:	69.9 KB
ID:	99083   Click image for larger version

Name:	100_0012.jpg
Views:	304
Size:	61.3 KB
ID:	99085  
Reply With Quote
The Following 3 Users Say Thank You to FArmstrong For This Post:
  #2  
Old 01-29-2011, 03:39:23 PM
G Willikers G Willikers is offline
Subscriber
 
Join Date: Mar 2006
Location: Canada
Posts: 10,851
Thanks: 9,987
Thanked 24,433 Times in 6,052 Posts
Default Re: Heider cone replacement

Fred,
I edited my post as I had said the friction was not a cone but a series of rings laminated together - but I see in your picture #3 that you already found that out! I have made up a couple of new sets by cutting rings out of sheet masonite - that seems to stand up well. Good luck.
G.

Last edited by G Willikers; 01-29-2011 at 11:08:47 PM.
Reply With Quote
The Following User Says Thank You to G Willikers For This Post:
  #3  
Old 01-29-2011, 07:45:51 PM
FWurth's Avatar
FWurth FWurth is offline
One Millionth Post
 
Join Date: Feb 2007
Location: Freeburg, Illinois, USA
Posts: 5,219
Thanks: 6,405
Thanked 4,467 Times in 2,366 Posts
Images: 4
Default Re: Heider cone replacement

Fred,

We need to do the same thing with our Heider as well, please keep the pictures coming! Are the sections full rings? Or are they in thirds or quarters?
Reply With Quote
  #4  
Old 01-30-2011, 01:16:09 PM
G Willikers G Willikers is offline
Subscriber
 
Join Date: Mar 2006
Location: Canada
Posts: 10,851
Thanks: 9,987
Thanked 24,433 Times in 6,052 Posts
Default Re: Heider cone replacement

Here's the old friction that was on the Beaver tractor. It had some meat left to it but was sort of glazed and wouldn't grip that well.
Still some of the original old green paint on it in spots though! Motor assembly slides ahead out of rear crankshaft bearing housing to replace friction.
G.
Attached Thumbnails
Click image for larger version

Name:	fric1.jpg
Views:	188
Size:	93.4 KB
ID:	99161   Click image for larger version

Name:	fric2.jpg
Views:	161
Size:	97.4 KB
ID:	99162  
Reply With Quote
The Following 6 Users Say Thank You to G Willikers For This Post:
  #5  
Old 01-30-2011, 02:32:44 PM
Paul Searl's Avatar
Paul Searl Paul Searl is offline
Subscriber
 
Join Date: Aug 2010
Location: Stockton, Illinois
Posts: 1,043
Thanks: 1,510
Thanked 3,601 Times in 717 Posts
Default Re: Heider Cone Replacement

we ordered our replacement disk through paperpulleys.com, not as cost effective as making your own from masonite, but maybe a little less hassle, although we still had to have it milled a little to fit.

you can unhook the linkage and use a bar to slide the engine farther forward to get the extra room. we also had to unbolt the angle iron underneath of it for it to drop out.

Keep the pictures coming, I wish we had taken pictures of the process.
Reply With Quote
The Following User Says Thank You to Paul Searl For This Post:
  #6  
Old 01-30-2011, 04:12:36 PM
FArmstrong FArmstrong is offline
Registered-III
 
Join Date: Feb 2007
Location: Valparaiso, Indiana
Posts: 212
Thanks: 643
Thanked 306 Times in 87 Posts
Default Re: Heider Cone Replacement

More pictures of the tractor. First one shows come-along pulling engine forward.
Fred
Attached Thumbnails
Click image for larger version

Name:	100_0011.jpg
Views:	209
Size:	83.7 KB
ID:	99208   Click image for larger version

Name:	100_0007.jpg
Views:	234
Size:	97.5 KB
ID:	99209  
Reply With Quote
The Following 5 Users Say Thank You to FArmstrong For This Post:
  #7  
Old 01-30-2011, 04:06:54 PM
FArmstrong FArmstrong is offline
Registered-III
 
Join Date: Feb 2007
Location: Valparaiso, Indiana
Posts: 212
Thanks: 643
Thanked 306 Times in 87 Posts
Default Re: Heider cone replacement

FWurth:
It appears the sections are full rings which are pressed in tight right now. Not sure if I should get a screwdriver in there and start peeling them out or if there is a better way...
Fred

---------- Post added at 02:06 PM ---------- Previous post was at 02:01 PM ----------

Paul,
We used a come-along to slide the engine forward but we have not cleared the shaft from the rear housing yet. Are there bearings inside of that housing? Is there anything (lip) on the shaft that will keep the shaft from exiting the housing?
Fred
Reply With Quote
The Following User Says Thank You to FArmstrong For This Post:
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Cone Head Rivets? dbyam Steam Stationary Engines, Traction Engines, Steam Boats 53 11-04-2013 10:53:20 PM
Blacksmith's cast iron cone? darrelld Blacksmithing and Metallurgy 2 12-24-2007 10:42:15 AM
Ball or Cone for Hercules? Chris Kirk Antique Engine Archives 1 09-15-2002 07:23:53 PM
1/2 inch Ball or Cone Mufflers Hal Davis Antique Engine Archives 0 09-10-2002 12:12:19 PM
Stuck governor cone Brian Antique Engine Archives 3 01-10-2002 07:25:28 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 05:13:42 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277