Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® General Discussion > Trucks, Trailers and Hauling for Shows
Forgot Password? Join Us!

Notices

Trucks, Trailers and Hauling for Shows The ins and outs of setting up a show trailer and getting it to and from the engine show. Please be fully aware of our web site Terms of Use Disclaimer as you read. Safety first!

Trucks, Trailers and Hauling for Shows

Hub Grease fittings


this thread has 4 replies and has been viewed 3638 times

Reply
 
Thread Tools Display Modes
  #1  
Old 10-12-2013, 02:08:20 PM
ronny p 148 ronny p 148 is offline
Registered
 
Join Date: May 2009
Location: Vermont, USA
Posts: 2,115
Thanks: 704
Thanked 622 Times in 274 Posts
Default Hub Grease fittings

Two years ago gad to take a wheel off trailer to replace broken brake shoe springs and adjustment screw. I cleaned out bearings of old grease and refilled hub with many pumps of grease to fill bearing and hub. Centrifugal force forced grease out of rubber grease fitting cap made mess of rims. I noticed dry rotted rubber cap on one of hubs took cap off looks like it could use some grease. Only 1000 miles since last grease job . How many pumps of grease do the hubs need and after how many miles ?

Ronny
Reply With Quote
Sponsored Links
  #2  
Old 10-12-2013, 04:18:25 PM
Andrew Mackey Andrew Mackey is offline
Moderator
 
Join Date: Nov 2004
Location: Rockaway, New Jersey USA
Posts: 14,133
Thanks: 1,990
Thanked 6,760 Times in 4,297 Posts
Exclamation Re: Hub Grease fittings

Usually a hand packing of the bearings and a fingerfull in the cap is enough. Centrifical force will keep grease in the bearings for the duration. As long as the wheels are not submerged, usually a good quality grease will least a year. 1 pump once in a great while should be ebough to keep it fresh. Once a year, the bearings need to be cleaned out with kerosene, blown dry and be inspected for wear or chipping. If all good, hand repacked until grease comes out the back of the bearing clean, and then re-installed. Overfilling the bearing space is a killer of seals and is unessescary. Once grease blows out a seal, contaminants like water and road salts will quickly wipe out the bearings and possibly the hub as well.

If the wheel is submerged, especially if the hub is warm or hot, then the bearing should be removed and cleaned at the nearest opportunity. The new soap complex greases used on autos will turn into a caustic mess if subjected to water

Andrew
Reply With Quote
  #3  
Old 10-12-2013, 09:23:40 PM
ronny p 148 ronny p 148 is offline
Registered
 
Join Date: May 2009
Location: Vermont, USA
Posts: 2,115
Thanks: 704
Thanked 622 Times in 274 Posts
Default Re: Hub Grease fittings

These bearings are not the type you pack by hand they have a grease fitting in hub cap with rubber cap that seals hub where grease fitting is.


Ronny
Reply With Quote
  #4  
Old 03-26-2015, 01:13:34 AM
Charlie1925 Charlie1925 is offline
Subscriber
 
Join Date: May 2009
Location: Acworth, Georgia, USA
Posts: 559
Thanks: 3,199
Thanked 473 Times in 268 Posts
Default Re: Hub Grease fittings

All wheel bearings are to be greased/packed by hand! I have packed bearings on jet airplanes, cargo airplanes, passenger airplanes, semi tractors & trailers, mobile homes, travel trailers, all types farm tractors/equipment ,cars, garden tractors and a whole lot of other stuff . Believe me when you pack the bearing,( you know that the dam thing is greased right. Don't lessen to this bull about greasing with A grease gun, they want you to have trouble so they can sell you a new BEARING /AXLE & HUB. THE GREASE GUN THING IS TO REGREASE AFTER A FEW HUNDRED MILES MAYBE A THOUSAND OR SO.

---------- Post added at 01:13 AM ---------- Previous post was at 12:47 AM ----------

also you jack up the axle/ wheel, grease slow ane you turn the wheel, that way you don't blow the seal, maybe 2 shots
Reply With Quote
The Following User Says Thank You to Charlie1925 For This Post:
  #5  
Old 03-26-2015, 04:50:56 AM
Dale Barnett's Avatar
Dale Barnett Dale Barnett is offline
Registered
 
Join Date: Jul 2009
Location: Wellsville, New York
Posts: 502
Thanks: 459
Thanked 333 Times in 190 Posts
Default Re: Hub Grease fittings

I was always told that the grease fittings were used to push water out after submerging not to grease the bearings.
I have had trailers with grease fittings and always pulled apart and cleaned & regrease once a year and knock on wood have never had a bearing go bad.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Rumely oil pull grease fittings Corey Robinson Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 4 05-30-2012 10:16:02 PM
Button tab grease fittings? steve Steam Stationary Engines, Traction Engines 13 06-26-2007 11:40:07 AM
Type of Grease in Grease cups Dale S Hit & Miss Gas Engine Discussion 17 04-16-2005 01:12:06 AM
Fittings ID help Andrew Albrecht Hit & Miss Gas Engine Discussion 1 01-30-2005 06:46:34 PM
1 1/2hp M grease fittings kevin hesse Antique Engine Archives 6 10-23-2004 01:37:50 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 07:31:20 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277