Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Shop Equipment Tools and Techniques > Air Compressors
Forgot Password? Join Us!

Notices

Air Compressors Restoration, Repair and use of Shop and Industrial Air Compressors

Air Compressors

Old Curtis C50 Air Compressor


this thread has 6 replies and has been viewed 1311 times

Reply
 
Thread Tools Display Modes
  #1  
Old 12-08-2017, 03:27:58 PM
Oilburnr Oilburnr is offline
Registered
 
Join Date: Dec 2017
Location: Virginia Beach, Virginia
Posts: 5
Thanks: 1
Thanked 1 Time in 1 Post
Default Old Curtis C50 Air Compressor

I bought this air compressor at an auction, don't know much about it except it was used up until the shop closed down a few years ago. Air compressors are somewhat foreign to me, as I've always just had cheapo direct drive oil free units. It's a Curtis Toledo, pics are attached, but serial number on the ID tag says C50U 43L83009

I know quite often these old units will last for decades, but I know no history on it and would like to make sure it's in good shape and stays that way. I've been afraid to take it apart because I haven't been able to find any manuals or quite frankly any information at all on this particular compressor. Oil is full and clean, air filter needs replacement, it turns over nice and smooth, and that's as far as I've gotten. Tank had a couple gallons of water in it when I got it, drained out almost completely clear, little bit of oil
Attached Thumbnails
Click image for larger version

Name:	15127609517831892920842.jpg
Views:	258
Size:	123.9 KB
ID:	297901   Click image for larger version

Name:	15127609837562052014690.jpg
Views:	196
Size:	198.9 KB
ID:	297902   Click image for larger version

Name:	1512761021754637873366.jpg
Views:	192
Size:	100.0 KB
ID:	297903   Click image for larger version

Name:	1512761041455907992442.jpg
Views:	186
Size:	211.7 KB
ID:	297904  
Reply With Quote
Sponsored Links
  #2  
Old 12-08-2017, 03:56:57 PM
Andrew Mackey Andrew Mackey is offline
Moderator
 
Join Date: Nov 2004
Location: Rockaway, New Jersey USA
Posts: 14,149
Thanks: 1,992
Thanked 6,767 Times in 4,301 Posts
Exclamation Re: Old Curtis C50 air compressor

Disconnect the outlet piping and plug the compressor outlet side with a reducer and 200 pound guage. Turn the compressor by hand and note resistance to turning. As each piston comes up, resistance should be about equal. Continue turning until it gets hard to turn or you get to around 150 PSI. Turn the crank and feel each side against pressure. if one side turns easier, possible worn rings or cylinder. If the guage pressure falls off, again rings or possibly outlet reeds or check valves. if you hear air escaping out the intake, bad inlet checks. If pressure holds, all is good, and one other thing to check. Turn the crank so that the pistons are about 1/2 way up and down, then rock the crank. Any clanking, or if the crank turns a bit before rod contact is taken up, and you will have to do teardown. if all is quiet, you probably have a nice compressor.

water in the reservoir is from condensation. The tank should be drained daily! You will get a little oil, but not too much - nature of the beast. if you are using for tools, just a filter and water seperater should be good. if for painting, a filter and dryer should be used.

If used indoors, I would use an SAE 30 compressor oil. NOT Automotive! Compressor oil is formulated differently. There should be either a sight level or a fill level that will tell you how much oil you need. The fill plug may have a dipstick too. DO NOT overfill! A good equipment shop that sells aod or maintains compressors should have the oil for it. NAPA auto may have it also.
Reply With Quote
  #3  
Old 12-08-2017, 09:49:16 PM
G.M.Johnson G.M.Johnson is offline
Subscriber
 
Join Date: Jul 2015
Location: Ann Arbor, Michigan
Posts: 379
Thanks: 191
Thanked 260 Times in 141 Posts
Default Re: Old Curtis C50 air compressor

Not a bad compressor at all. That unit is a dual piston single stage and was made in the 60's. Change the oil out and give it a whirl! If the oil looks fairly clean chances are it is good to go. Curtis compressors of that era are pretty darn tough. Rings and bottom don't wear out as much as the valves do. Over time the springs fatigue and break appart and get lodged between the disc and seat. Good news is you can still get valve parts from some suppliers.
Reply With Quote
  #4  
Old 04-30-2019, 11:02:00 AM
Oilburnr Oilburnr is offline
Registered
 
Join Date: Dec 2017
Location: Virginia Beach, Virginia
Posts: 5
Thanks: 1
Thanked 1 Time in 1 Post
Default Re: Old Curtis C50 Air Compressor

After a year and a half of work consuming most of my free time, I've finally gotten a chance to get back to work in the hobby shop. The motor on this compressor was toast, and I put it on the back burner.

Picked up a harbor freight special 2hp motor for it, changed the oil, and she's pumping great! So nice and quiet too, running around 465rpm.

Only concern I have is that there does not seem to be any unloader on this compressor. Did some compressors not come with them? Is there any way I could add one? Above 90psi the motor definitely struggles to get her goin
Reply With Quote
  #5  
Old 04-30-2019, 12:35:05 PM
Vanman Vanman is offline
Subscriber
 
Join Date: Aug 2011
Location: Mission Viejo, California
Posts: 6,117
Thanks: 10,230
Thanked 2,904 Times in 1,942 Posts
Default Re: Old Curtis C50 Air Compressor

Did you find out what was wrong with the original motor? Often times it is something simple. Old motors are one of my favorite things about old machines. While it'll do inna pinch, that china motor will not be nearly as good.

Don't know about the unloaders on this make. If not centrifugal on the back of the pump, then perhaps it's in the pressure switch...

Keith
Reply With Quote
  #6  
Old 05-30-2019, 09:07:37 PM
Oilburnr Oilburnr is offline
Registered
 
Join Date: Dec 2017
Location: Virginia Beach, Virginia
Posts: 5
Thanks: 1
Thanked 1 Time in 1 Post
Default Re: Old Curtis C50 Air Compressor

Pressure switch is just your standard square D unit mounted to the tank. The existing motor was a marathon electric 1-1/5hp and was just tired. Caps were bad, corrosion inside, and the place I brought it to see about fixing it said it was a cheap motor from the 90s and not worth fixing. I ended up rewiring the HF motor to 240v and it seems to do a little better. The 120v wiring is not up to the task. When it kicked on around 90psi the voltage dropped to 87.
Reply With Quote
  #7  
Old 06-03-2019, 01:35:20 AM
84prerunner 84prerunner is offline
Registered
 
Join Date: May 2014
Location: Covina, california, USA
Posts: 21
Thanks: 1
Thanked 3 Times in 3 Posts
Default Re: Old Curtis C50 Air Compressor

Back in the day my dad had a similar compressor that had a hard time starting under load (would pop breakers). He added a T in the line between the pump and tank and added a small surge tank. Not even sure what the surge tank was, i just remember a green tank hanging on there. It was probably half the size of a coffee can and made all the difference in letting this thing start. Just something to consider.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Curtis air compressor jimbo8259 Farm Antiques and Collectibles 2 07-13-2016 11:23:58 AM
Curtis Compressor eserdy Farm Antiques and Collectibles 11 10-17-2014 07:13:36 AM
curtis compressor Kevin Hit & Miss Gas Engine Discussion 16 01-22-2012 09:50:22 PM
Curtis compressor Denis Rouleau Antique Engine Archives 4 05-16-2004 11:21:39 PM
Curtis Air Compressor Wesley Phillips Antique Engine Archives 6 11-29-2002 04:06:39 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 07:55:34 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277