Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Scale Model Engineering
Forgot Password? Join Us!

Notices

Scale Model Engineering Steam, gas and hot air model engines, tractors, trains and accessories. Machining and milling castings.

Scale Model Engineering

Root & Vandervoot Model Broke


this thread has 0 replies and has been viewed 281 times

Reply
 
Thread Tools Display Modes
  #1  
Old 09-07-2019, 07:40:05 PM
Bob N Bob N is offline
Subscriber
 
Join Date: Nov 2004
Location: Lena, Illinois, USA
Posts: 123
Thanks: 48
Thanked 74 Times in 45 Posts
Default Root & Vandervoot Model Broke

Hi

************************************************** *********************
Thanks to all who have looked, we have acquired the information from a local modeler is lending us his prints

************************************************** *********************



I am posting this on a couple of boards.

A friend of mine has a 1/2 scale of a 1hp horizontal hopper cooled Root & Vandervoot engine. He purchased it completed and has been using it for a while. Today, at a show of course, the shaft that holds the big timing gear and the latch broke. One of the legs of the “U” that forms the support for the latch broke off. It looked like there was barely any metal holding the leg together. We do not have the prints so before we go pulling it apart I have a couple of questions.

On the inside of the base I can see the end of the shaft, it looks like there is a allen type cap screw recessed in the end of the shaft. Not sure what this is for. There is a bolt on the base casting going into the shaft hole and that clearly is what holds the shaft in place. The question is what is the cap screws' function?

We are assuming we can figure out the dimension’s but it would be nice to know what is what before we just pull the shaft out and have stuff flying all over the place.

What we really need is the drawing for the shaft. Just a picture of the shaft area of the drawing page would be great, do not need anything else. Or a hand drawn sketch.

Is there anyone out there who built this engine and can tell us what to expect? Has anyone else had this issue?

Thanks

Bob

Last edited by Bob N; 09-08-2019 at 10:10:27 AM.
Reply With Quote
Sponsored Links
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Root & Vandervoot igniter points Tim Venetis Hit & Miss Gas Engine Discussion 4 10-06-2014 07:10:19 PM
8 HP Root & Vandervoot on Craigslist DaveHC Hit & Miss Gas Engine Discussion 5 01-10-2012 10:07:17 AM
Root & Vandervoort 5/16 Scale Model of 4HP Horizontal, any videos? Don Siefker Hit & Miss Gas Engine Discussion 2 01-14-2011 04:11:08 PM
Root & Vandervoort 5/16 Scale Model of 4HP Horizontal tank cooled, any videos? Don Siefker Scale Model Engineering 3 01-01-2010 09:37:15 PM
Kurtz & Root 12V w/ Briggs Model A engine John Newman, Jr. Generators & Electric Motors General Discussion 20 06-06-2005 09:46:24 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 04:24:13 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277