Antique Tractors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Old Iron and Tractor Community > Antique Steel Wheel Tractors - Old Iron Lugs and Cleats
Forgot Password? Join Us!

Notices

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats Photos and information about antique steel wheeled farm tractors. This is where to find the heaviest of Old Iron tractors.

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats

Early style two-cylinder Kinnard Haines Tractors


this thread has 73 replies and has been viewed 21952 times

Reply
 
Thread Tools Display Modes
  #61  
Old 12-14-2014, 12:28:01 AM
Benjamin Roth's Avatar
Benjamin Roth Benjamin Roth is offline
Subscriber
 
Join Date: Nov 2005
Location: Elgin, North Dakota USA
Posts: 163
Thanks: 244
Thanked 790 Times in 78 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Here is another view of the place. The building in the center is the Blacksmith shop built in 1924. It had a 5 hp. Faultless powering a line shaft with an air compressor, pedestal grinder, post drill, 25 lb. trip hammer, and a lathe. The other red building to the right and in the distance was the elevator built in 1926. It had a 6 hp. Field engine in the basement later replaced with a 6 hp. M International and eventually an electric motor. You can see how the iron is all spread out. Lots of time was spent sweeping with a metal detector and prying things out of the ground.


The brochure picture of the tractor has a muffler below the left cylinder. I'm not sure if this is correct for the tractor but it was in the pile. If it's for something else does anyone recognize it?


I had posted this in the other thread with the single cylinder tractor. I think it's a neat signature piece for the tractor. The bolt in the clevis was loose and would still turn out by hand!


The drawbar guide. It's interesting to see the blacksmith work on these parts.


Some front axle parts. The K 68 number is the same on the 40-70 Flour City tractors. Looking at the original tractor picture Jeff Wahl posted Here it appears the front axle casting is the same as the later tractors like the 40-70.
Attached Thumbnails
Click image for larger version

Name:	DSCN1403.JPG
Views:	1678
Size:	256.3 KB
ID:	213380   Click image for larger version

Name:	DSCN4216.JPG
Views:	1670
Size:	289.2 KB
ID:	213381   Click image for larger version

Name:	DSCN4179.JPG
Views:	1682
Size:	275.9 KB
ID:	213382   Click image for larger version

Name:	DSCN3906.JPG
Views:	1683
Size:	283.7 KB
ID:	213383  

Reply With Quote
Sponsored Links
  #62  
Old 12-19-2014, 01:24:22 PM
acat65 acat65 is offline
Registered-I
 
Join Date: Oct 2011
Location: Lebanon, Indiana USA
Posts: 69
Thanks: 69
Thanked 59 Times in 27 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

at least I don't think Ben will be setting at the local bar all day Gene
Reply With Quote
The Following User Says Thank You to acat65 For This Post:
  #63  
Old 12-20-2014, 11:35:02 PM
Jeff Wahl's Avatar
Jeff Wahl Jeff Wahl is offline
Subscriber
 
Join Date: Nov 2004
Location: Fairfax, Virginia
Posts: 1,252
Thanks: 3,641
Thanked 9,788 Times in 944 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Here is another photo of a two cylinder Flour City tractor:

__________________
-Jeff

wahlengines.com
Reply With Quote
  #64  
Old 12-29-2014, 01:59:43 PM
Jeff Wahl's Avatar
Jeff Wahl Jeff Wahl is offline
Subscriber
 
Join Date: Nov 2004
Location: Fairfax, Virginia
Posts: 1,252
Thanks: 3,641
Thanked 9,788 Times in 944 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Scanned this in the other day:

__________________
-Jeff

wahlengines.com
Reply With Quote
  #65  
Old 01-03-2015, 05:07:01 PM
retrofit88 retrofit88 is offline
Registered-III
 
Join Date: May 2012
Location: Roxbury, CT
Posts: 234
Thanks: 501
Thanked 2,165 Times in 208 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Happy New Year All.
Benjamin,
Please let us know what parts you have for the Little Bull. Thank you for posting all the pictures.
Reply With Quote
The Following User Says Thank You to retrofit88 For This Post:
  #66  
Old 01-05-2015, 07:42:42 PM
OTTO-Sawyer's Avatar
OTTO-Sawyer OTTO-Sawyer is online now
Subscriber
 
Join Date: Nov 2008
Location: Scioto Mills, Illinois USA
Posts: 8,235
Thanks: 16,202
Thanked 6,950 Times in 3,363 Posts
Photo Re: Early style two-cylinder Kinnard Haines Tractors

Somehow I missed this thread before, but figured I'd repost a picture I posted in another Kinnard Haines thread now that I saw the catalog shot Tom posted in Post #11.

I have the Original picture from the Reed Brothers unit in front of the barn and a couple other shots of it.

Figured they may as well be shown together.
Attached Thumbnails
Click image for larger version

Name:	fcity11.jpg
Views:	205
Size:	162.9 KB
ID:	215152   Click image for larger version

Name:	Reed Brothers threshing rig & Shredding North of Afolke Illinois.jpg
Views:	224
Size:	112.6 KB
ID:	215153  
__________________
I just keep coming back again and again like the Evil Twin of a Bad Penny !
http://www.youtube.com/user/oldSawyer?feature=watch
Reply With Quote
The Following 11 Users Say Thank You to OTTO-Sawyer For This Post:
  #67  
Old 01-05-2015, 08:16:43 PM
Tim Colwell's Avatar
Tim Colwell Tim Colwell is offline
Subscriber
 
Join Date: Oct 2013
Location: Montgomery, Minnesota, USA
Posts: 1,107
Thanks: 944
Thanked 967 Times in 465 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

That thresher has an interesting stacker!
Reply With Quote
The Following User Says Thank You to Tim Colwell For This Post:
  #68  
Old 01-07-2015, 01:00:14 AM
Benjamin Roth's Avatar
Benjamin Roth Benjamin Roth is offline
Subscriber
 
Join Date: Nov 2005
Location: Elgin, North Dakota USA
Posts: 163
Thanks: 244
Thanked 790 Times in 78 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Nikki, all the Bull parts I had went to another collector. There were only two or so parts so there wasn't much at all. All the parts I had for other tractors are also gone now to help pay for the Flour City project.

Otto, that is interesting to see an original picture to compare to the catalog. I had done some scaling from the two cylinder drawing in the catalog but it seemed like the proportions weren't matching what I already knew. I thought the catalog was more artistic than it was photograph.

Here is a picture of some fresh castings for the tractor!

Attached Thumbnails
Click image for larger version

Name:	150106_002.jpg
Views:	961
Size:	61.8 KB
ID:	215287  
Reply With Quote
  #69  
Old 01-23-2015, 07:41:14 PM
OTTO-Sawyer's Avatar
OTTO-Sawyer OTTO-Sawyer is online now
Subscriber
 
Join Date: Nov 2008
Location: Scioto Mills, Illinois USA
Posts: 8,235
Thanks: 16,202
Thanked 6,950 Times in 3,363 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Quote:
Originally Posted by Tim Colwell View Post
That thresher has an interesting stacker!
As per the 'testimonial' they sent in with their picture the thresher is an Advance 32x52 with self feeder and attached stacker.

They also mention the shredder in the other picture as being a 12 roll Advance Husker Shredder.

I believe they were already using BOTH of the Advance units with their previous power source which was a large portable engine.

__________________
I just keep coming back again and again like the Evil Twin of a Bad Penny !
http://www.youtube.com/user/oldSawyer?feature=watch
Reply With Quote
The Following User Says Thank You to OTTO-Sawyer For This Post:
  #70  
Old 12-18-2015, 11:59:33 PM
Tim Colwell's Avatar
Tim Colwell Tim Colwell is offline
Subscriber
 
Join Date: Oct 2013
Location: Montgomery, Minnesota, USA
Posts: 1,107
Thanks: 944
Thanked 967 Times in 465 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Ben,
Did you ever find or make any new parts?
__________________
Tim Colwell
JD & IHC corn sheller and engine collector.
Reply With Quote
  #71  
Old 12-23-2015, 11:53:38 PM
Benjamin Roth's Avatar
Benjamin Roth Benjamin Roth is offline
Subscriber
 
Join Date: Nov 2005
Location: Elgin, North Dakota USA
Posts: 163
Thanks: 244
Thanked 790 Times in 78 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Tim,

No, did not find any new parts or even leads. I haven't made any new parts yet either, too busy with other projects. I am slowly working on modeling the entire tractor with CAD and have about 40% finished. The frame itself has been taking a lot of time because of all the unknowns.

I attached two pictures showing the collection of parts as they are now. There are a few 20-35 FC parts and possibly a few things that are something else entirely. It may not look like much but I am excited to get started on this project.


Attached Thumbnails
Click image for larger version

Name:	DSCN3605.JPG
Views:	537
Size:	280.9 KB
ID:	242101   Click image for larger version

Name:	DSCN3606.JPG
Views:	537
Size:	280.1 KB
ID:	242102  
Reply With Quote
  #72  
Old 09-05-2017, 11:12:24 AM
Tim Colwell's Avatar
Tim Colwell Tim Colwell is offline
Subscriber
 
Join Date: Oct 2013
Location: Montgomery, Minnesota, USA
Posts: 1,107
Thanks: 944
Thanked 967 Times in 465 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Ben,
I thought you were behind this but forgot to ask when I met you. Any new castings or progress?
__________________
Tim Colwell
JD & IHC corn sheller and engine collector.
Reply With Quote
  #73  
Old 09-12-2017, 12:05:49 AM
Benjamin Roth's Avatar
Benjamin Roth Benjamin Roth is offline
Subscriber
 
Join Date: Nov 2005
Location: Elgin, North Dakota USA
Posts: 163
Thanks: 244
Thanked 790 Times in 78 Posts
Default Re: Early style two-cylinder Kinnard Haines Tractors

Hi Tim,

It was nice meeting you at Rollag. There have been a few more castings poured. More is in the works but will take awhile yet. The goal for now is to start assembly next fall.
Reply With Quote
The Following 4 Users Say Thank You to Benjamin Roth For This Post:
  #74  
Old 09-12-2017, 07:14:55 AM
Don Selmer Don Selmer is offline
Subscriber
 
Join Date: Nov 2004
Location: Cottage Grove, Wisconsin, USA
Posts: 1,646
Thanks: 5,010
Thanked 3,052 Times in 835 Posts
Images: 15
Default Re: Early style two-cylinder Kinnard Haines Tractors

Ben, I sent you a PM
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Kinnard-Haines Flour City David Parfitt Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 205 Today 09:01:16 AM
Kinnard Haines - Flour City Tractor Chris J Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 1 11-23-2010 10:48:11 PM
Kinnard - Haines Co. Engines Denis Rouleau Antique Gas Engine Discussion 4 09-26-2009 06:08:39 AM
Early Style Steam Elbows Dusty Antique Gas Engine Discussion 6 11-06-2008 12:06:08 PM
CARB PARTS FOR AN EARLY STYLE WATERLOO Aaron Abey Antique Engine Archives 0 08-08-2003 09:48:10 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 05:59:56 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277