Generators and Motors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Shop Equipment Tools and Techniques > Welding Shop
Forgot Password? Join Us!

Notices

Welding Shop Welder generators, equipment, weld practice, techniques, troubles and solutions. See our TERMS of SERVICE prior to reading!

Welding Shop

Vise help


this thread has 7 replies and has been viewed 398 times

Reply
 
Thread Tools Display Modes
  #1  
Old 05-02-2019, 08:45:54 PM
Barnbikes Barnbikes is offline
Registered-II
 
Join Date: Nov 2004
Location: Saint Francis, Minnesota
Posts: 198
Thanks: 4
Thanked 633 Times in 87 Posts
Default Vise help

Picked this vise up lately. Previous owner beat the front so badly that it cracked (caved in) the frame.

Can it be welded or should I just donate it to china?

It is never going to see any hard use - maybe I can just drill a hole and use a bolt and nut to secure the crack.
Attached Thumbnails
Click image for larger version

Name:	1.JPG
Views:	147
Size:	106.8 KB
ID:	333982   Click image for larger version

Name:	2.JPG
Views:	151
Size:	114.5 KB
ID:	333983  
Reply With Quote
The Following 2 Users Say Thank You to Barnbikes For This Post:
Sponsored Links
  #2  
Old 05-02-2019, 09:09:09 PM
dalmatiangirl61 dalmatiangirl61 is online now
Subscriber
 
Join Date: Feb 2010
Location: San Marcos, Texas / McGill, Nevada
Posts: 4,678
Thanks: 5,599
Thanked 4,001 Times in 1,969 Posts
Default Re: Vise help

You can always try to braze or silver solder it, how long it will last is another question. Ixne on welding, it will most likely just crack more/again.
__________________
Those who can see the invisible, can do the impossible
Reply With Quote
  #3  
Old 05-02-2019, 10:04:57 PM
CharlieB CharlieB is offline
Registered-I
 
Join Date: Dec 2014
Location: Severn, Maryland, USA
Posts: 340
Thanks: 26
Thanked 169 Times in 127 Posts
Default Re: Vise help

Appears to be made of low grade Chinesium cast iron.
Cracking too extensive for reasonable repair, even for light duty work.
Buy similar at Harbor Fright for around $60 and use this one for a boat anchor.
Reply With Quote
  #4  
Old 05-02-2019, 10:46:06 PM
slip knot slip knot is online now
Subscriber
 
Join Date: Jan 2014
Location: Texas Gulf Coast
Posts: 1,531
Thanks: 1,087
Thanked 1,415 Times in 666 Posts
Default Re: Vise help

While I cant disagree that its cheap chineseum potmetal that probably should be on the next scrap boat headed back. I see a learning experience here.
If it was mine, I'd drill the end, V the crack a bit, throw it on the gas grill for a few hours at max heat and then try welding it up. I bought 10lbs of nickle rod a while back, maybe try brazing. I've even watched a Utube of some guy running mig wire into cast. Whatcha got to lose other than a little time and some materials. That's how I learn the best, trial and error.
Reply With Quote
The Following User Says Thank You to slip knot For This Post:
  #5  
Old 05-02-2019, 11:22:06 PM
CharlieB CharlieB is offline
Registered-I
 
Join Date: Dec 2014
Location: Severn, Maryland, USA
Posts: 340
Thanks: 26
Thanked 169 Times in 127 Posts
Default Re: Vise help

Preheat and nickel rod. Been there, done that. (My trial and error) Worked great with good old American cast iron. Failed miserably with the Chinesium. Must be all the impurities.
Reply With Quote
  #6  
Old 05-03-2019, 01:40:16 AM
cobbadog cobbadog is offline
Registered-III
 
Join Date: Aug 2009
Location: Coopernook. N.S.W. Australia
Posts: 1,589
Thanks: 2,958
Thanked 674 Times in 466 Posts
Default Re: Vise help

When I was a little nipper Pa bought home a vice from work that had suffered the same outcome. First get the guy that does this type of work out of the workshop permanently so it doesn't happen again. Using a vice as an anvil will never end well.
Back to the vice I know of. When Pa showed me his new 8" vice with a big grin on his dial I asked about the repair/weld/braze on the back jaw. Well once it broke Pa grabbed it and took it to the blacksmiths shop and got them to heat it up and then he applied his craft of using bronze to do the repair. It was chiselled out by hand before the repair was done as technology had been basic back then (over 50 years back now) for repairing but that vice is still in use in my shed now. I must admit that I use the vice as what it was intended for but from time to time I do look for a small anvil for flogging things out on.
Reply With Quote
  #7  
Old 05-03-2019, 02:29:56 PM
beezerbill beezerbill is offline
Subscriber
 
Join Date: Sep 2012
Location: Boulder, Colorado
Posts: 1,171
Thanks: 181
Thanked 631 Times in 423 Posts
Default Re: Vise help

Should give the previous owner an anvil and a rubber hammer - you know the rest.
Reply With Quote
The Following User Says Thank You to beezerbill For This Post:
  #8  
Old 05-07-2019, 02:25:32 PM
Langes Machine Shop Langes Machine Shop is offline
Subscriber
 
Join Date: Mar 2009
Location: Hector, Minnesota, USA
Posts: 287
Thanks: 256
Thanked 789 Times in 176 Posts
Default Re: Vise help

It could be welded with bronze. Nickle will not work!!! But you will have more into it than it is worth.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Machineist vise ronny p 148 Machine Shop and Tool Talk 5 07-08-2016 10:27:11 AM
Vise grips Wayne Riedlinger Machine Shop and Tool Talk 9 12-29-2015 12:52:25 PM
Anvil Vise Brian.P Blacksmithing and Metallurgy 6 08-26-2014 07:13:39 AM
Unknown Vise ID wheelhorseman Farm + Industrial Antiques and Collectibles 1 03-01-2013 09:52:54 PM
What is this vise? redfish443 Machine Shop and Tool Talk 8 12-26-2009 10:50:15 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 11:22:23 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277