Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® General Discussion > Smokstak Down Under
Forgot Password? Join Us!

Notices

Smokstak Down Under For Australia and New Zealand Smokstakers to meet, greet, yabber and yack.

Smokstak Down Under

About Time for an Engine Video


this thread has 211 replies and has been viewed 24690 times

Reply
 
Thread Tools Display Modes
  #1  
Old 08-03-2016, 05:06:17 PM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,725
Thanks: 1,774
Thanked 2,032 Times in 1,088 Posts
Default About Time for an Engine Video

Hello all
I've noticed of late there has not been much in the way of pictures or video's of our pride and joys. It's been blah, blah, blah.
So here is one of our latest little projects. We wanted a little engine setup so we could travel to a few rallies. Van on the back, engine in the back sort of thing. The whole setup easily goes in the back of the old Pajero with room left over for another little engine and something for it to drive.
Anyways, here's our little Barlow and Triton. I've just had it at a rally where it ran for 2 days with virtually no problems. A valve got a bit sticky and some oil blew out the breather into the magneto points were the only problems. A squirt of oil here and a squirt of degreaser there and problems sorted. The oil blowing out the breather was entirely my fault. I didn't leave the oil level plug out long enough when I topped the oil up at the beginning of the second day. Stupid me.

Please feel free to add pictures or video's of your...well, any old stuff. No need to be an old engine per-say. Let everyone know why your in this hobby.
Cheers Scott

Reply With Quote
The Following 12 Users Say Thank You to Scotty 2 For This Post:
Sponsored Links
  #2  
Old 08-03-2016, 06:19:22 PM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,725
Thanks: 1,774
Thanked 2,032 Times in 1,088 Posts
Default Re: About time for an engine video

Having it's first run at a rally

Reply With Quote
The Following 5 Users Say Thank You to Scotty 2 For This Post:
  #3  
Old 08-03-2016, 06:34:07 PM
Burrows75 Burrows75 is offline
Registered
 
Join Date: May 2016
Location: Gold Coast, Queensland, Australia
Posts: 48
Thanks: 20
Thanked 31 Times in 15 Posts
Default Re: About time for an engine video

Just after I got the Fuller Johnson Farm Pump running.



https://youtu.be/cuQ8Lsskl1U
Reply With Quote
The Following 3 Users Say Thank You to Burrows75 For This Post:
  #4  
Old 08-03-2016, 08:14:07 PM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,725
Thanks: 1,774
Thanked 2,032 Times in 1,088 Posts
Default Re: About time for an engine video

Quote:
Originally Posted by Burrows75 View Post
Just after I got the Fuller Johnson Farm Pump running.
Hello Burrows
Thanks for that. You certainly know when she fires don't you?

Cheers Scott
Reply With Quote
  #5  
Old 08-03-2016, 08:49:35 PM
Van Helsing Van Helsing is offline
Registered-I
 
Join Date: Sep 2015
Location: Hunter Valley, New South Wales, Australia
Posts: 78
Thanks: 12
Thanked 49 Times in 23 Posts
Default Re: About time for an engine video

........

Here's a You Tube thingo of my 1914 Fuller Johnson farm pumper running ( if the link works that is ? )

Lookey here:-

https://www.youtube.com/watch?v=KXY9AD5W0h8

.......
Reply With Quote
The Following 3 Users Say Thank You to Van Helsing For This Post:
  #6  
Old 08-04-2016, 03:19:17 AM
sunshineman sunshineman is offline
Registered-II
 
Join Date: Jul 2015
Location: Sydney, NSW, Australia
Posts: 524
Thanks: 489
Thanked 475 Times in 232 Posts
Default Re: About time for an engine video

Just a couple from the collection

My 1915 sunshine 5hp
https://youtu.be/j0bTueMo_r0

My Mcdonald imperial super diesel (cc)
https://youtu.be/5vAtYxjlRhM

My sons southern cross farm pumper
https://youtu.be/SCTkLyAa-HE

Regards, sunshineman
Reply With Quote
The Following 5 Users Say Thank You to sunshineman For This Post:
  #7  
Old 08-04-2016, 05:08:30 AM
ianoz ianoz is offline
Registered-I
 
Join Date: Mar 2010
Location: Gladstone Queensland Australia
Posts: 233
Thanks: 314
Thanked 292 Times in 120 Posts
Default Re: About time for an engine video

Steeleye trying his hand at unstationary engines .
https://www.youtube.com/watch?v=2xq0IR_VV1s
Reply With Quote
The Following 2 Users Say Thank You to ianoz For This Post:
  #8  
Old 08-04-2016, 06:05:32 AM
isandian isandian is offline
Registered-I
 
Join Date: Nov 2010
Location: Sydney, NSW, Australia
Posts: 356
Thanks: 422
Thanked 337 Times in 164 Posts
Default Re: About time for an engine video

Thought I might try my hand at a couple of videos.

This is my McDonald ML 65-70HP hot bowl semi-diesel running for the first time in a number of years. Despite a metre of concrete in the base, the whole thing shakes badly at higher revs. Original muffler (a WW2 sea mine casing).

https://youtu.be/xKDaA6nG05o

Another McDonald semi-diesel, this time a 40HP model TL being given its first run after having replaced its piston and conrod after finding the original flogged out.

https://youtu.be/3X-fUMcuZZo

Ian
Reply With Quote
The Following 2 Users Say Thank You to isandian For This Post:
  #9  
Old 08-04-2016, 06:32:02 AM
Patrick M Livingstone's Avatar
Patrick M Livingstone Patrick M Livingstone is offline
Registered-III
 
Join Date: Nov 2004
Location: Sydney, Australia
Posts: 1,908
Thanks: 5,017
Thanked 4,921 Times in 1,051 Posts
Images: 4
Default Re: About time for an engine video

I finally had some time last weekend to give my little Austral a run. I have owned this engine since I was a teenager (a long time ago). It is a very well worn engine but runs well. After a crazy week, it is relaxing to give something in the garage a run.
Patrick

Patrick
Reply With Quote
The Following User Says Thank You to Patrick M Livingstone For This Post:
  #10  
Old 08-04-2016, 08:14:19 AM
Burrows75 Burrows75 is offline
Registered
 
Join Date: May 2016
Location: Gold Coast, Queensland, Australia
Posts: 48
Thanks: 20
Thanked 31 Times in 15 Posts
Default Re: About time for an engine video

I picked up this Buzacott Farm Pump with the Fuller Johnson. The Buzacott had fallen onto it's nose at some time and bent the crank. I also found (after purchase ) that it was seized as well. Another crank and freeing he stuck piston and away it went. This one also has a bark out the exhaust. Just working out a windmill pump so it could be displayed doing its job.

https://youtu.be/OwOAh7ksXOs

Adam
Reply With Quote
The Following User Says Thank You to Burrows75 For This Post:
  #11  
Old 08-04-2016, 08:53:04 AM
sunshineman sunshineman is offline
Registered-II
 
Join Date: Jul 2015
Location: Sydney, NSW, Australia
Posts: 524
Thanks: 489
Thanked 475 Times in 232 Posts
Default Re: About time for an engine video

Hi ian
My cc mcdonald looks like a model compared to yours . Still even the little ones are big lumps of iron .regards sunshineman
Reply With Quote
The Following User Says Thank You to sunshineman For This Post:
  #12  
Old 08-04-2016, 11:16:59 PM
Nathan Woodruff Nathan Woodruff is offline
Registered-I
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 382
Thanks: 490
Thanked 537 Times in 182 Posts
Default Re: About time for an engine video

My little Sundial running. https://www.youtube.com/watch?v=py9ILU8Rukw
Good to see a thread like this. It's a good idea and great to see other enthusiasts engines running.
Regards, Nathan
Reply With Quote
The Following 3 Users Say Thank You to Nathan Woodruff For This Post:
  #13  
Old 08-06-2016, 08:13:01 PM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,725
Thanks: 1,774
Thanked 2,032 Times in 1,088 Posts
Default Re: About time for an engine video

Hello all
Thanks for all the videos. Those McDonalds are big chucks of iron for sure.
I'm amased how, so called, same engines run. Two exact same engines can sit side by side and they both will have a different sound and characteristics....and still run very well. I don't now if it's wear that creates that difference or personality. The pumpers in this thread are prime examples.
Nathan's Sundial is another. Ours sound similar but there are slight differences.

I'll be giving our latest engine a run later. A video will be taken if it runs well or not. What's the bet it'll play up now I've said that

Who else is up for submitting a video?

Cheers and thanks
Scott
Reply With Quote
  #14  
Old 08-06-2016, 09:53:02 PM
isandian isandian is offline
Registered-I
 
Join Date: Nov 2010
Location: Sydney, NSW, Australia
Posts: 356
Thanks: 422
Thanked 337 Times in 164 Posts
Default Re: About time for an engine video

Here is another of my McDonalds, this time a petrol engine dating to 1918. It's no mean beast, either, and I can only start it with a 6.5HP Honda with reduction drive. Restoration started out with these bits.

Here it is running.

https://youtu.be/NKYz2fv4FS4
Attached Thumbnails
Click image for larger version

Name:	2005_1029N0005.jpg
Views:	95
Size:	134.1 KB
ID:	259786  
Reply With Quote
The Following 3 Users Say Thank You to isandian For This Post:
  #15  
Old 08-06-2016, 10:02:45 PM
Nathan Woodruff Nathan Woodruff is offline
Registered-I
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 382
Thanks: 490
Thanked 537 Times in 182 Posts
Default Re: About time for an engine video

Here is a short video of one of my McDonalds under a bit of load https://www.youtube.com/watch?v=unLKlV3nERk It is a very worn out engine and has already had 4 full rebuilds in it's working life. It puts on a good show at night.
Reply With Quote
The Following 2 Users Say Thank You to Nathan Woodruff For This Post:
  #16  
Old 08-07-2016, 03:45:51 AM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,725
Thanks: 1,774
Thanked 2,032 Times in 1,088 Posts
Default Re: About time for an engine video

Hello all
Gee wizz Isandian, I have to tip my hat to you in the restoration you did on the petrol McDonald. I can only dream of having the skills you must have.

So I gave the latest engine a run today. A Ronaldson-Tippett badged Gane CH diesel. This morning it was still on the trailer from the rally at Pimpama last week-end, so it needed to be unlaoded, cleaned, run and put to bed.
The rally was the first time I've had it running for more then 3 minutes. I got her going in Brisbane, in between working on our house there, so I kinda did not to run her for long due to consideration for the neighbours. She ran really well all week-end, but there are some issues that need attention like a new trolley instead of this workshop trolley, a new fuel line with piggy tails, new exhaust pipe with a slightly larger dia., fix hopper shaking etc etc. Something else I have to fix is a crack in the tappet cover. She tipped over when I was loading her for the rally. You can see where she landed each side of the badge. Another good reason to build a better trolley.
The next run for her will do her the world of good. She'll be on a pump all day chugging away under a bit of load.

When you look at the pictures, you may notice there is no decompression lever like the Ronny badged CH's. I wonder why?
But anyways I'm waffling.
Cheers Scott

Reply With Quote
The Following 2 Users Say Thank You to Scotty 2 For This Post:
  #17  
Old 08-07-2016, 05:08:42 AM
Patrick M Livingstone's Avatar
Patrick M Livingstone Patrick M Livingstone is offline
Registered-III
 
Join Date: Nov 2004
Location: Sydney, Australia
Posts: 1,908
Thanks: 5,017
Thanked 4,921 Times in 1,051 Posts
Images: 4
Default Re: About time for an engine video

My previous video seems to have failed to work so here is a link to the YouTube clip of my little Austral:
https://www.youtube.com/watch?v=NIr0mCR6EQU

Lurking behind the Austral in my Stover YC 6hp throttler. Such a sweet running engine:
https://www.youtube.com/watch?v=NIr0mCR6EQU

Patrick
Reply With Quote
The Following 2 Users Say Thank You to Patrick M Livingstone For This Post:
  #18  
Old 08-07-2016, 06:32:00 AM
sunshineman sunshineman is offline
Registered-II
 
Join Date: Jul 2015
Location: Sydney, NSW, Australia
Posts: 524
Thanks: 489
Thanked 475 Times in 232 Posts
Default Re: About time for an engine video

Hi scotty
The ute in the back ground looks like a datsun p312 .I had a sedan version .it is no longer in my possesion I sold it to a japanese collector to take back to japan .I will post some photos.
Regards sunshineman
Reply With Quote
  #19  
Old 08-07-2016, 06:46:36 AM
isandian isandian is offline
Registered-I
 
Join Date: Nov 2010
Location: Sydney, NSW, Australia
Posts: 356
Thanks: 422
Thanked 337 Times in 164 Posts
Default Re: About time for an engine video

Hi Patrick, Both videos appear to be the same (Stover). Ian
Reply With Quote
  #20  
Old 08-07-2016, 07:16:30 AM
Patrick M Livingstone's Avatar
Patrick M Livingstone Patrick M Livingstone is offline
Registered-III
 
Join Date: Nov 2004
Location: Sydney, Australia
Posts: 1,908
Thanks: 5,017
Thanked 4,921 Times in 1,051 Posts
Images: 4
Default Re: About time for an engine video

Quote:
Originally Posted by isandian View Post
Hi Patrick, Both videos appear to be the same (Stover). Ian
You can never see too much of a throttle governed Stover
One more try for my baby lamp Austral:



https://www.youtube.com/watch?v=xmOJ07-zElA

Patrick
Reply With Quote
The Following User Says Thank You to Patrick M Livingstone For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Old Time Video Full of Machinery - Be warned, no gas engines! MFaris Antique Gas Engine Discussion 1 01-08-2018 08:34:59 AM
Sawing down a big tree one piece at a time. Interesting video OTTO-Sawyer YouTube Old Iron Videos 10 03-05-2013 03:36:24 PM
Blast back into time 1904 in the Westinhouse Engine Factory - Video Wayne Grenning Antique Gas Engine Discussion 13 11-13-2012 07:28:51 AM
Awesome video - Triumph Spitfire Engine Rebuild Time-Lapse Video KD5BYB Antique Gas Engine Discussion 6 07-01-2012 12:07:33 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 10:31:22 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277