Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Small Air Cooled Gasoline Engines > Wisconsin Engines
Forgot Password? Join Us!

Notices

Wisconsin Engines Single cylinder up to V4 engines.

Wisconsin Engines

Key Way Groove Alignment


this thread has 4 replies and has been viewed 464 times

Reply
 
Thread Tools Display Modes
  #1  
Old 10-04-2018, 01:32:27 PM
pfc123 pfc123 is offline
Registered
 
Join Date: Oct 2016
Location: Bridgewater, New Jersey, USA
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Thumbs down Key Way Groove Alignment

Should the key way groove in shaft be lined up with the timing groove on flywheel?
Reply With Quote
Sponsored Links
  #2  
Old 10-04-2018, 06:44:33 PM
Ozlander Ozlander is offline
Registered
 
Join Date: Jun 2016
Location: Rose Hill, Kansas
Posts: 34
Thanks: 0
Thanked 13 Times in 12 Posts
Default Re: Key way groove allignment

How are you going to get the key in if they don't align?
Reply With Quote
The Following User Says Thank You to Ozlander For This Post:
  #3  
Old 10-04-2018, 08:54:51 PM
CharlieB CharlieB is offline
Registered-I
 
Join Date: Dec 2014
Location: Severn, Maryland, USA
Posts: 297
Thanks: 26
Thanked 135 Times in 105 Posts
Default Re: Key way groove allignment

Don't count on it.
Install the flywheel on the crankshaft, insert a probe into #1 spark plug hole, carefully rotate the crank until the piston is at top dead center, and mark the flywheel.
Reply With Quote
  #4  
Old 10-04-2018, 10:26:59 PM
slip knot slip knot is offline
Subscriber
 
Join Date: Jan 2014
Location: Texas Gulf Coast
Posts: 1,361
Thanks: 906
Thanked 1,224 Times in 581 Posts
Default Re: Key Way Groove Alignment

Back when I used to hotrod SBC engines , a degree wheel was a very important tool in timing the engine. it was amazing how far off some of the timing chain gears were.
Reply With Quote
  #5  
Old 10-05-2018, 06:47:43 PM
Zira Zira is offline
Subscriber
 
Join Date: Nov 2004
Location: Apex, North Carolina, USA
Posts: 1,687
Thanks: 364
Thanked 468 Times in 356 Posts
Default Re: Key Way Groove Alignment

If you are asking if the key way on the output side should line up, the answer is usually, if there is no clutch or gear reduction.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Victaulic groove lock fittings. sftyvlv1 Steam Stationary Engines, Traction Engines, Steam Boats 3 11-01-2015 11:57:24 AM
Lister(oid) CS ring groove clearance krawlr Vintage Diesel and Oil Engines 2 10-30-2012 12:01:25 AM
Singh groove John in Maryland Antique Gas Engine Discussion 1 06-11-2009 10:16:39 PM
Removing the pins in a piston groove? Gene Fisher Antique Gas Engine Discussion 7 04-19-2006 11:16:49 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 12:05:11 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277