Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Small Air Cooled Gasoline Engines > Wisconsin Engines
Forgot Password? Join Us!

Notices

Wisconsin Engines Single cylinder up to V4 engines.

Wisconsin Engines

Wisconsin AEN on a Howard Rotovator


this thread has 1 replies and has been viewed 364 times

Reply
 
Thread Tools Display Modes
  #1  
Old 07-02-2018, 08:02:09 PM
transman05 transman05 is offline
Registered
 
Join Date: May 2018
Location: Chico, California, USA
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Default Wisconsin AEN on a Howard Rotovator

I am repairing a late 50s Howard Gem and need a piece for the AEN that is bolted up to it. This was an import from the UK, and it is my understanding that these units were shipped engineless to the states and then the dealer would power it, most likely with these Wisconsin engines.
Those of you familiar with these may know the rear flywheel is secured by a large nut which also contains a pilot bearing in the back side. Im repairing the trans and refurbishing much of the adjoining pieces hoping to bring some good life back to the machine. I have the rotovator parts ordered from UK, but the nut/bearing is not in their vocabulary.
Any suggestions as to where I can source this item would be great.
Thanks in advance.
Dan
Reply With Quote
Sponsored Links
  #2  
Old 07-13-2018, 11:17:18 PM
s100 s100 is offline
Registered-II
 
Join Date: Jan 2008
Location: Detroit, Michigan, USA
Posts: 825
Thanks: 204
Thanked 486 Times in 334 Posts
Default Re: Wisconsin AEN on a Howard Rotovator

Just ran across your post and saw you have no replies. I for one cannot visualize what you have going on there. I am guessing it is something unique to the Howard as most Wisconsin AEN's have a rope starting sheave on the end of the flywheel but I think the Howards start with a crank in the body of the machine. I know there are several Howard people on this site so maybe if you included a picture of the area in question you might get some useful replies.

Since the standard Wisconsin rope starting sheave and the flywheel retaining nut are incorporated into one piece, if you are missing the correct Howard nut etc. maybe you could find a Wisconsin sheave and use it to rope start the engine.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Howard Gem Rotovator Twin Cylinder 180 degree Crank stano316 Garden Tractors / Mowers / Scooters 12 07-01-2018 06:21:28 PM
Howard Gem rotavator w/wisconsin 2 cyl. ariensman Wisconsin Engines 4 04-24-2017 07:48:57 AM
Howard Gem earlyevo Garden Tractors / Mowers / Scooters 2 03-19-2015 09:40:43 PM
Howard Gem G24 Rotavator - Wisconsin TJD K-Tron Garden Tractors / Mowers / Scooters 3 08-31-2011 11:55:09 PM
Howard "GEM" Rotovator Jonathan Widelo Garden Tractors / Mowers / Scooters 17 11-20-2010 11:16:52 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 01:17:18 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277