Generators and Motors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Vintage Electrical Equipment > Generators & Electric Motors General Discussion > Onan Generators
Forgot Password? Join Us!

Notices

Onan Generators Restoring, operating and maintaining vintage Onan generators.

Onan Generators

Onan 7.5JB - Wiring


this thread has 75 replies and has been viewed 2641 times

Reply
 
Thread Tools Display Modes
  #71  
Old 02-09-2017, 11:17:37 PM
kiteoregon kiteoregon is offline
Registered
 
Join Date: Jan 2017
Location: Portland, Oregon
Posts: 30
Thanks: 7
Thanked 2 Times in 1 Post
Default Re: Onan 7.5JB - Wiring

So far, I have removed the rotor through stud bolt, the bolts on the stator through stud as well as the cover. I can't however move the end bell at all. I have been following the YD major service manual page 16, i think i am stuck on step 5. Can anybody provide some pro tips to get this thing removed?

Also 3/4 of the stator through studs un-threaded with the bolts on them, should i get the bolts off and thread them back in, or does it make any difference?

Here is the doc i have been using:
http://www.twinslan.net/~n0nas/manua...0(10-1975).pdf

Thanks.
Reply With Quote
Sponsored Links
  #72  
Old 02-09-2017, 11:30:35 PM
nothingbutdarts nothingbutdarts is offline
Sponsor
 
Join Date: Apr 2014
Location: Bailey, Colorado, USA
Posts: 2,639
Thanks: 5,991
Thanked 1,286 Times in 835 Posts
Default Re: Onan 7.5JB - Wiring

If memory serves me correctly, put the thru stud back in, just leave the nut off.

Getting the end bell off, try using a flat bar of some sort and smacking the raised ridge on the bell where it meets the stator, do it all around the bell and see if that does not break it loose.

For pulling the stator, I would leave the two top thru studs screwed in to help support the stator as you gently slide it out once you break it loose. I believe there are small screw driver size slots between it and the bell housing. Also do not forget to unplug F1 and F2 from the end bell.

Rotor, take a solid block of wood, aluminum or something and smack at least 4 places around the rotor on the bare steel area. Not on the windings or the poles!!! It is a taper fit on the crankshaft. I like to put the nut back on the thru stud so as to not have it slide back and fall off when it breaks loose, once loose remove nut and carefully slide it off. I hope this helps.

Last edited by nothingbutdarts; 02-10-2017 at 12:20:46 AM. Reason: spelling
Reply With Quote
  #73  
Old 02-09-2017, 11:45:52 PM
BigBlockChev's Avatar
BigBlockChev BigBlockChev is offline
Subscriber
 
Join Date: Jan 2007
Location: Coquitlam, BC, Canada
Posts: 2,035
Thanks: 364
Thanked 1,546 Times in 909 Posts
Default Re: Onan 7.5JB - Wiring

Try to get a biggish 2 jaw puller on to the end bell. If you reinsert the rotor center through bolt and install a second nut for the puller to bear on make sure to get the correct thread size as it is not a coarse thread or you can use a small socket to push on. The 4 stator bolts have to be removed but then you can tighten the puller and either the stator and end bell will come off the rear bearing together or the end bell will come by itself then you can pull the endbell free as it comes off the rear bearing. If the stator stays put it can be loosened by whacking it with a 2x4, usually it wont take much. This leaves the rotor in place. In your case you may not have to remove the rotor to check the stator. If you do need to remove the rotor you can loosen the rotor through bolt a couple of turns to give it some slack. Then whack the side of the rotor with a hammer cushioned by a piece of hardwood or a big brass hammer so as not to damage the laminations of the rotor. The through bolt will prevent the rotor from falling off and getting damaged. You will be able to see the rotor move when it breaks loose but check to see after every time after you hit it. Then you can remove the through bolt while supporting the rotor with a big block of wood or something, the rotor is heavy!!. Don't remove the rotor if you don't have to!! Cheers Dan
__________________
It's always something simple.
One test is worth a thousand guesses.
If some is good and more is better then too much is just enough
Reply With Quote
  #74  
Old 10-12-2017, 12:11:55 PM
kiteoregon kiteoregon is offline
Registered
 
Join Date: Jan 2017
Location: Portland, Oregon
Posts: 30
Thanks: 7
Thanked 2 Times in 1 Post
Default Re: Onan 7.5JB - Wiring

Bringing an old thread back to life, this generator sat un-touched since my last posts. The weather has changed and we had our first power outage. Now i am back on getting this thing working.

Model: 7.5JB
Serial: A960597423
Spec: 68774E

I have pulled the stater / winding, they look very crispy. What is the best course of action, try to find somebody to rebuild this or purchase a working gen head? Attached are the pictures of the gen side of the problem.

Thanks.
Attached Thumbnails
Click image for larger version

Name:	IMG_20171011_165719.jpg
Views:	38
Size:	255.1 KB
ID:	293377   Click image for larger version

Name:	IMG_20171011_165708.jpg
Views:	37
Size:	172.4 KB
ID:	293378   Click image for larger version

Name:	IMG_20171011_165727.jpg
Views:	38
Size:	132.8 KB
ID:	293379  
Reply With Quote
  #75  
Old 10-12-2017, 06:42:55 PM
Max Thompson Max Thompson is offline
Sponsor
 
Join Date: May 2009
Location: N.W. Missouri, USA
Posts: 5,956
Thanks: 5,251
Thanked 5,646 Times in 3,017 Posts
Default Re: Onan 7.5JB - Wiring

Looks like the "Magic Smoke" has left the generator.

Yes, it is time to look for another JB. You now know a little more about what to look for. You might get lucky and find one that has a seized motor with a good gen section.

You now have a bunch of spare engine parts though.
Reply With Quote
  #76  
Old 10-12-2017, 08:36:43 PM
BigBlockChev's Avatar
BigBlockChev BigBlockChev is offline
Subscriber
 
Join Date: Jan 2007
Location: Coquitlam, BC, Canada
Posts: 2,035
Thanks: 364
Thanked 1,546 Times in 909 Posts
Default Re: Onan 7.5JB - Wiring

As it happens I have couple of 7.5 JB genheads attached to partly functional MDJE generators which I could be pursuaded to part with for reasonable money. But you would have to come get one of them. I bought 8 7.5 MDJEs in the last year and am never going to get to all of them. I actually drove down to Portland to get a few. These would be 120/240V genends so you would get full output. PM me if you are interested. Cheers Dan
__________________
It's always something simple.
One test is worth a thousand guesses.
If some is good and more is better then too much is just enough
Reply With Quote
The Following User Says Thank You to BigBlockChev For This Post:
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Onan 5.0 CCK wiring help Handyhiker1 Onan Generators 16 08-26-2015 07:12:49 AM
Onan wiring help on 2.5 AJ PecosPhil Onan Generators 5 07-29-2013 10:05:45 PM
Onan 4.0 Gen set wiring help Bwill Onan Generators 5 08-13-2011 07:41:25 PM
Hot Wiring a 4 CCK Onan c east Onan Generators 3 04-11-2011 08:17:58 PM
Onan CCK wiring sam c Onan Generators 2 06-23-2008 01:33:06 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 10:15:39 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277