Antique Tractors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Old Iron and Tractor Community > Antique Steel Wheel Tractors - Old Iron Lugs and Cleats
Forgot Password? Join Us!

Notices

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats Photos and information about antique steel wheeled farm tractors. This is where to find the heaviest of Old Iron tractors.

Antique Steel Wheel Tractors - Old Iron Lugs and Cleats

Case 18-32 K Project


this thread has 53 replies and has been viewed 5702 times

Reply
 
Thread Tools Display Modes
  #1  
Old 11-27-2017, 10:35:16 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Case 18-32 K Project

Some years ago there was a late 18-32 on a farm auction near here, i remember it had L Case looking wheels on it so it had to be late 1928 i assume. I was the runner up bidder, always thought i might end up with one someday. A friend called a little over a week ago and wanted to sell me this one, terms and conditions were very reasonable. Picked it up last friday on the long weekend.
This one will actually have to wait its turn until after a few other projects, but everyone except my wife thought it would be good to get it in the schedule.
This one spent its working life in Wyoming, then went to South Dakota, finally here to Kansas.
Attached Thumbnails
Click image for larger version

Name:	IMG_4317.jpg
Views:	280
Size:	131.0 KB
ID:	297129   Click image for larger version

Name:	IMG_4319.jpg
Views:	587
Size:	203.5 KB
ID:	297130  
Reply With Quote
The Following 9 Users Say Thank You to Russ Hamm For This Post:
Sponsored Links
  #2  
Old 11-27-2017, 10:44:00 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K project

Even though it will be on the backburner, i had to check out for any damage or parts needed. I already knew that the manifold was welded and ready by a previous owner, and the head was done. For some reason a piston was broken on top, possibly from trying to loosten up the engine. It looks to me like they had it loose at one time and now its stuck again, the broken piston being at the bottom of its stroke. Strangely, the oil pan looks like it hadn't been removed since it was in use. Seems like they were trying to loosten up the engine all at once instead of one piston at a time. AND, it looks to me like the #3 piston should have been the worst stuck, #4 piston being the one beat and broken.
Attached Thumbnails
Click image for larger version

Name:	008.jpg
Views:	303
Size:	82.8 KB
ID:	297131  
Reply With Quote
  #3  
Old 11-27-2017, 10:54:19 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K project

I removed the oil pan saturday, and was lowering it down with my sons' help. As it came down he said; "wonder what that is in there?" Found a governor weight piece that had been laying in there awhile, and after further investigation found another piece up higher in the block. Pulled the governor cover off and found that someone had replaced the governor weight without looking for the pieces. While the cover was off i ran a magnet in the cavity looking for more pieces. Found 2/3rds of a TOOTH.
With all good hope i pulled the timing cover to see if they had also changed a gear when the governor went south. No such luck, the tooth matches up perfectly on the cam gear.
So far, aside from the cam gear it looks like the bearing for the governor/ accesory drive shaft needs replaced and the governor needs buhings badly.
Attached Thumbnails
Click image for larger version

Name:	004.jpg
Views:	320
Size:	183.7 KB
ID:	297132   Click image for larger version

Name:	006.jpg
Views:	324
Size:	130.5 KB
ID:	297133   Click image for larger version

Name:	005.jpg
Views:	366
Size:	182.7 KB
ID:	297134  
Reply With Quote
The Following 3 Users Say Thank You to Russ Hamm For This Post:
  #4  
Old 11-27-2017, 11:00:24 AM
G Willikers G Willikers is offline
Subscriber
 
Join Date: Mar 2006
Location: Canada
Posts: 12,420
Thanks: 11,803
Thanked 28,098 Times in 7,100 Posts
Default Re: Case 18-32 K project

Russ,
Great looking tractor. Congratulations on getting it.
Unforeseen problems, eh? That's what makes it such good fun. Look at it this way, you will probably make some new friends in your search for parts!
Good luck with it.
Reply With Quote
The Following User Says Thank You to G Willikers For This Post:
  #5  
Old 11-27-2017, 11:29:42 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K project

Yes, actually my friend who sold the tractor has quite a few parts available anyway. We knew it would probably need some things, didn't know how much was neglect, these tractors saw less maintainece towards the end of thier use in many cases.
The pan is very easy to remove, why they didn't go that route first to remove broken parts, second to pull pistons, i'm not sure.
Reply With Quote
  #6  
Old 12-04-2017, 07:11:58 PM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K project

Anybody know what to use on the 18-32 for sleeve o-rings? Got the pistons out last weekend, may have to pull some sleeves to clean out the furnishings from the last tennants. Looks like they were carpeting.
Reply With Quote
  #7  
Old 12-04-2017, 07:53:09 PM
J Ware J Ware is offline
Subscriber
 
Join Date: Nov 2011
Location: Morrice, Michigan
Posts: 590
Thanks: 309
Thanked 915 Times in 332 Posts
Default Re: Case 18-32 K project

Russ, an old mechanic friend had a kit for making his own Orings. He bought it at Detroit Ball Bearing, I believe they're name is Applied now. Be worth lookig into, Jim
Reply With Quote
  #8  
Old 02-13-2018, 06:05:56 PM
80 case 80 case is offline
Registered-I
 
Join Date: Dec 2013
Location: Fargo,ND
Posts: 50
Thanks: 22
Thanked 71 Times in 32 Posts
Default Re: Case 18-32 K project

Found a place called The O-ring Store in Clarkston, Washington they made the sleeve gaskets for my 12-20 crossmotor. There phone number is(208)413-6377 hope this helps!
Reply With Quote
The Following 2 Users Say Thank You to 80 case For This Post:
  #9  
Old 09-25-2018, 08:56:51 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K Project

The Case sat for awhile in front of the shop, had the sleeves and crank throws greased, a cardboard cutout covering the block and a tarp over it all. Last night I went to start working on getting it ready to go in the shop and sure enough, a rat had built a nest on top of the cardboard and cousin mouse or two had ate through the carboard into the block. The number four sleeve was out so they managed to pull some insulation out of the water jacket and up onto the top of the block. That done it, plywood this time instead of cardboard, will have to pull the block anyway to clean out the water jacket.

My big question now, I noticed what I think is a freeze crack in the water jacket wall facing into the lifter valley. Has anyone had similar? I was pretty disappointed at first, but after looking it over I think it has never leaked, there is still plenty of oil residue on the wall and no leak trail. The oil pan is clean, no rust. I'm going to pull the block and at least one other sleeve so we can clean and look it over.
Sorry but I had to use a flashlight for a flash, pics are poor but I had a mirror to look it over and im sure its a crack, half moon shaped above the cast-in tube in the bottom of the lifter valley.
Attached Thumbnails
Click image for larger version

Name:	DSCF0076.jpg
Views:	200
Size:	89.8 KB
ID:	319508   Click image for larger version

Name:	DSCF0077.jpg
Views:	205
Size:	95.7 KB
ID:	319509  
Reply With Quote
The Following 2 Users Say Thank You to Russ Hamm For This Post:
  #10  
Old 10-01-2018, 09:38:31 AM
Russ Hamm's Avatar
Russ Hamm Russ Hamm is online now
Subscriber
 
Join Date: Dec 2005
Location: Canton, Kansas, USA
Posts: 1,537
Thanks: 1,060
Thanked 2,405 Times in 801 Posts
Images: 1
Default Re: Case 18-32 K Project

As the mice pretty much packed the water jacket up and I needed to pull the sleeves to inspect the inner crack this weekend I pulled the block. I hate it when I pull a sleeve and all that crap falls on the crank and in the crankcase.
I saw a thread here where someone had pulled the block and exposed the crank, its actually pretty easy.
The wood under the gas tank looked like the center piece had been on fire at some time or another. The water pump feels like there is something inside trying to turn it into a grinder, and the fan gears must be in pretty worn shape, another fan set came with it.
Attached Thumbnails
Click image for larger version

Name:	DSCF0104.jpg
Views:	171
Size:	113.2 KB
ID:	319985   Click image for larger version

Name:	DSCF0112.jpg
Views:	175
Size:	159.3 KB
ID:	319986   Click image for larger version

Name:	DSCF0113.jpg
Views:	175
Size:	168.1 KB
ID:	319987   Click image for larger version

Name:	DSCF0109.jpg
Views:	153
Size:	86.1 KB
ID:	319988  
Reply With Quote
The Following 3 Users Say Thank You to Russ Hamm For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
22-40 Case Project Craig A Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 31 12-16-2015 08:14:40 PM
18-32 Case New Project Camerons Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 15 06-07-2015 09:44:20 PM
Case 15-27 crossmotor new project. neilthewheel Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 4 03-10-2012 11:46:01 PM
Case 12-20 New Project Camerons Antique Steel Wheel Tractors - Old Iron Lugs and Cleats 21 12-28-2011 07:47:52 PM
New project, Case 500 turbo Antique Farm Tractors 10 11-20-2007 12:07:12 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 12:19:25 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277