Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® General Discussion > Smokstak Down Under
Forgot Password? Join Us!

Notices

Smokstak Down Under For Australia and New Zealand Smokstakers to meet, greet, yabber and yack.

Smokstak Down Under

Ronaldson and Tippett Type N Compression


this thread has 3 replies and has been viewed 267 times

Reply
 
Thread Tools Display Modes
  #1  
Old 01-11-2019, 02:07:34 AM
Pollardd Pollardd is online now
Registered
 
Join Date: Aug 2018
Location: Grafton, New South Wales, Australia
Posts: 25
Thanks: 2
Thanked 8 Times in 6 Posts
Default Ronaldson and Tippett Type N Compression

Hi Guys,
I have a Ronaldson and Tippett Type N Engine that I'm trying to get going again.
It has sat for a very long time in someone's shed but I think it has faired fairly well.

Click image for larger version

Name:	CompressionTest.jpg
Views:	80
Size:	168.0 KB
ID:	326132

It still turns freely and I'm thinking I can avoid pulling every last nut and bolt apart on it.

There wasn't anything in the sump when I got it but it wasn't dry as a chip either.

I squirted some old around the place and let it sit for a few weeks while I worked on mounting the magneto.

I put a compression tester on it and cranked the handle around half a dozen times and the needle on the gurage reads about 50 psi. I squirted some more oil down the spark plug hole and the reading didn't change.

What should I expect a reasonable reading to be to get this engine going?

What should I expect a reasonable reading to be if I expect it to put out some "horses power" and actually do something?

I don't have a load planned yet but I'll probably want to run a water pump or a 12v generator.

I couldn't find any original specification for this value.

Thanks in advance
David
Reply With Quote
The Following 2 Users Say Thank You to Pollardd For This Post:
Sponsored Links
  #2  
Old 01-11-2019, 04:34:56 AM
Combustor Combustor is offline
Registered-II
 
Join Date: Jul 2009
Location: North of West Australia
Posts: 710
Thanks: 3
Thanked 346 Times in 266 Posts
Default Re: Ronaldson and Tippett Type N Compression

Hello David,
The Ronnie N series are nice little motors.Yours would have been tank cooled, but should be OK to test run a few minutes without water.
You will be able to assess its condition easily if you can get it to run, so give it fuel oil and spark and see what happens. 50 psi should be enough to make it run, as often they get e bit of carbon or grit under valve seats, and a short run will clear it out and restore full compression, probably over 100 psi at a guess. Someone here will have an accurate figure I am sure, but if it starts and runs reliably then you are good to go. Think most of them rated between 2 and 3 hp round 800 to 1200 rpm. Play with spark and fuel settings till it sounds happy.
Plough Book Sales probably have handbooks for sale. Enjoy your li'l Ronnie.
Kind regards,
Combustor.
Reply With Quote
  #3  
Old 01-11-2019, 03:22:59 PM
Scotty 2 Scotty 2 is offline
Registered-III
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,507
Thanks: 1,605
Thanked 1,796 Times in 970 Posts
Default Re: Ronaldson and Tippett Type N Compression

Hello David
Your engine seems to be in great original condition. A good find. Do you have the hopper or the cooling tank flanges? I see the hard to get brass nuts there.

The Ronny N played big part in Australian rural life and many a collection has started with one. It also amases me as to the number of variations the good old Ronny N has. They may all look the same until you really look at them.

What HP rating is it?
The good old Ronny doesn't need much compression to run and I wouldn't be too concerned about 50 psi. She'll run fine on it. To do a compression test I'd slip the carby off.
As Combustor has said, the compression may get better with a good run. Get her running first to see how things go. If our want to do something, give the valves a clean and maybe a valve grind or lap.
I've never actually tested how much compression a Ronny N has. I might have to do that one day. It couldn't be too high. The crank handles aren't too long in their swing and there's no magic start button to press.

I also wouldn't worry too much about maximum power. Running a pump as a display doesn't need much power at all.

Cheers Scott

Last edited by Scotty 2; 01-11-2019 at 04:46:54 PM.
Reply With Quote
  #4  
Old 01-11-2019, 08:08:24 PM
cobbadog cobbadog is offline
Registered-III
 
Join Date: Aug 2009
Location: Coopernook. N.S.W. Australia
Posts: 1,444
Thanks: 2,771
Thanked 616 Times in 418 Posts
Default Re: Ronaldson and Tippett Type N Compression

Give it a start up once you have the maggy timed and cleaned the carby out and some good oil in his guts. Run it slowly at first and then keep altering the revs once at running temp. Obviously you will need to keep it cool somehow, even if it is just a garden hose on slowly putting water through the system. So long as there is water at the top opening you have enough water inside as if it got too hot it would push the hot water out but the cool water from the hose should replace it.
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Ronaldson-Tippett Type N Engine Pollardd Antique Gas Engine Discussion 11 09-12-2018 08:03:28 PM
Ronaldson Tippett N Type cylinder liner ozbennett Smokstak Down Under 5 11-28-2016 10:53:25 PM
Ronaldson Tippett Type O jayvee Smokstak Down Under 9 05-31-2015 05:09:44 PM
What magneto do I need for a Ronaldson-Tippett type N? farnzy Magnetos, Ignition Coils and Spark Plugs 2 03-01-2013 03:54:26 AM
Ronaldson Tippett Type O jayvee Smokstak Down Under 0 11-10-2012 11:50:29 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 07:28:59 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277