Generators and Motors
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Vintage Electrical Equipment > Generators & Electric Motors General Discussion > Onan Generators
Forgot Password? Join Us!

Notices

Onan Generators Restoring, operating and maintaining vintage Onan generators.

Onan Generators

Onan MME model 9mme a 1a - Help Needed


this thread has 40 replies and has been viewed 1947 times

Reply
 
Thread Tools Display Modes
  #1  
Old 07-27-2017, 04:17:52 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default Onan MME model 9mme a 1a - Help Needed

EDIT: Threads combined and Title corrected. -- Harry

thanks for the shop manual it helps a lot it starts right up but as soon as you release the start button it dies.you have heard it before and i have done the research about low oil pressure,low voltage and overheated exhaust. i will try them as soon as i get the low pressure switch fixed. it went bad before and someone just added an extention to the junction block and put another switch on and when i went to take it off and the brass nippol fell apart so now i need to get that piece out of the block and fix it right those oil switches are not cheap the cheapest one is 80 bucks at napa. i think the owner has other problems as well like air in the oil but i am not sure he just changed the oil the day before i got there and it looked clear but with black chunks in it. and there is an antifreeze leak in the exhaust i think. there is green stuff on the tray under the gen set maybe that was from filling it. no white smoke so that is good. and it is on a fresh water boat that hardly ever gets run. it is a nice boat but it is 100 miles away one way so it is a trip to say the least. every time i go to buy the oil switch they ask me for the part no. so which is the original? at what is the low pressure shut off? so can get a generic shut off switch.
Reply With Quote
Sponsored Links
  #2  
Old 07-27-2017, 07:58:28 PM
Motorhead's Avatar
Motorhead Motorhead is offline
Subscriber
 
Join Date: May 2007
Location: Central Coast, California
Posts: 3,904
Thanks: 1,834
Thanked 2,700 Times in 1,400 Posts
Default Re: onan mme marine gen set

To help you the best, please post the FULL model and serial number of your set. There can be several reasons why your particular set won't stay running after you let off of the start switch. One reason can be because the generator isn't producing voltage. One other that I encountered with a late 7.5JB was that the oil pressure switch was stuck closed. You might try disconnecting the oil pressure switch and see if it will stay running.
Otherwise, you need to post the model and SN of the set.
Check the twinslan site and see if you can find the manuals for your set. Chances are it will have a wiring schematic for your set. The LETTER spec on the ID tag is important to further define which parts and diagrams are for your generator.
__________________
The Control panel
and gauges of my
7.5JB
Reply With Quote
The Following 2 Users Say Thank You to Motorhead For This Post:
  #3  
Old 07-29-2017, 08:21:28 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: onan mme marine gen set

i got the shop manual for the generator and the model no. is 9mme a 1a and the serial no. is I870940696 it is and older one and only get used about once a year because the owner is on shore power. how do i decode these no.s . i got a oil ressure switch on amazon for 27.oo it is for a genrac but i think they are the same.?
Reply With Quote
  #4  
Old 07-29-2017, 09:18:35 PM
MBB MBB is offline
Registered-III
 
Join Date: Apr 2009
Location: Elk Grove Village IL USA
Posts: 3,310
Thanks: 1,438
Thanked 2,856 Times in 1,447 Posts
Default Re: onan mme marine gen set

Is it possible it is a 9MME-1R/1A other wise I only find a 9MME-A/1C
Reply With Quote
  #5  
Old 07-29-2017, 09:22:18 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default onan mme model 9mme a 1a what are the specs

the owner just knows it is on his boat and will start when you push the switch and shut off when you release it. it's been worked on before and messed up like adding an extra pressure switch and leaving the old one in. i think there is a leak because the paint one the engine where the fitting goes into the block was missing so i am changing all that out and trying to fix the leaks. the gen doesn't get used but once a year for a few minutes. i went to turn the fittings to get the low pressure switch off and the fitting broke off. but i got an internal pipe wrench for 1/8 in pipes so it should be a minor hickup i will let you people know when i get the parts and get it installed. i got all three manuals so i am not totally lost.
Reply With Quote
  #6  
Old 08-01-2017, 04:23:01 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: onan mme marine gen set

that's possible. when the owner changed the oil he put 30 wt oil in it. is that too thick? i think the part came in. it's at a friends house in Spokane and he is hard to get a hold of.

yes that is possible. when the owner changed the oil he put 30 wt oil in is that too thick?\

yes that is possible, can these no.s be interpreted? when the owner changed the oil be put 30 wt oil in, is that too thick? it only has 20 lbs of oil pressure when it first starts up.

yes that is possible. the owner ,when he changed the oil out 30 wt oil in is this to thick. it only has 20 lbs oil pressure at idle. can someone interpret the model and serial no. it might give me more info.

sorry about the multiple replies my computer was having a brain fart (blame the computer)
Reply With Quote
  #7  
Old 08-08-2017, 06:20:54 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: onan mme marine gen set

i got the low pressure switch . it is from a generac generator it is the closest i could get in the time frame provided. if i ordered one from onan it would be 50 bucks from nashville tenn and eight weeks out maybe. are theses switches normally open or closed and why so expensive do they have gold in them.
Reply With Quote
  #8  
Old 08-11-2017, 09:40:16 PM
oldgenny oldgenny is offline
Registered
 
Join Date: Jul 2017
Location: Rosalia, Washington
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Default No ac input

I put a new pressure switch in that was not the problem. I think it is no ac. It is supposed to put out 90 volts ac to the control board and it doesn't.

Of course i am not sure how to check it as the manual doesn't look like the actual parts. It says something about a flash diode but it doesn't show where. Help!
Reply With Quote
  #9  
Old 08-11-2017, 09:52:58 PM
nothingbutdarts nothingbutdarts is offline
Sponsor
 
Join Date: Apr 2014
Location: Bailey, Colorado, USA
Posts: 2,643
Thanks: 6,004
Thanked 1,290 Times in 837 Posts
Default Re: No ac input

People have no idea what your refering to, are you posting in reference to this thread you started??


https://www.smokstak.com/forum/showthread.php?t=170493 (Threads combined -- Harry)

If so, you should just keep the older thread going and don't post back in this one.
Reply With Quote
The Following 12 Users Say Thank You to nothingbutdarts For This Post:
  #10  
Old 08-12-2017, 06:28:31 AM
KPack KPack is offline
Subscriber
 
Join Date: Feb 2016
Location: Bryan, Texas
Posts: 546
Thanks: 1,740
Thanked 425 Times in 218 Posts
Default Re: No ac input

I don't see any ac power either.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Onan Genset - help needed to identify model NomadAU Onan Generators 12 01-31-2017 02:10:08 AM
Onan model 60 DYA-15R/19566J electrical/manual needed shockingdave Onan Generators 6 12-31-2015 03:58:16 AM
onan model number needed bo4huskers Onan Generators 45 10-02-2014 07:01:53 PM
Onan wiring diagram needed for model 4.5PG-3P/1B dynabruce Onan Generators 1 12-09-2012 10:06:38 PM
Onan Model 4.0 DKC-3CR/1A info needed KWA915 Onan Generators 3 06-21-2012 10:23:04 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 09:23:16 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277