Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Vintage Electrical Equipment > Delco and other Low Voltage DC Light Plants
Forgot Password? Join Us!

Notices

Delco and other Low Voltage DC Light Plants Antique Generators, Light Plants, Typically 24, 32 or 48 volt although some are 110 volt. DC Lamps, Motors and appliances.

Delco and other Low Voltage DC Light Plants

Delco 752


this thread has 1 replies and has been viewed 1960 times

Reply
 
Thread Tools Display Modes
  #1  
Old 01-08-2001, 10:31:50 PM
Joe Murphy
Guest
 
Posts: n/a
Default Delco 752

Is the head removable on the752 to clean the carbon. Is there any thing I should know before removing the commutator as it is very oily in there. Also is there any one in the New York area (syracuse) that might be able to help me with the wiring on this light plant. Thanks Joe.
Reply With Quote
Sponsored Links
  #2  
Old 01-09-2001, 03:58:18 PM
Don C. Wiley
Guest
 
Posts: n/a
Default Re: Delco 752

The Model 752 does not have a removable head. It has a blind cylinder, and to remove it you must remove all the shroud and unbolt the cylinder from the crank case. The valve seats are so small and so close to the cylinder wall that I had to make a special valve re-seating tool to get the job done.

The commutator is an integral part of the armature and it has a tapered hole to fit the taper on the crank shaft. I had to make a special puller to get the armature off the crank shaft. Unless it is very bad I would leave it in place and clean it there. NAPA auto parts stores sell a electric motor and brake clean in a spray can. I use that to clean the armature and commutators. Just spray it liberally around and blow it off with compressed air.

I live in Illinois and can't "drop" by to help.

If your's has the automatic control panel, it is pretty tricky to make work. There is a reverse current relay that is usually bad. I finally just rewound the coils on two of my generators, before they would work.

I hope this is of some help to you and any other person who is "into Delcos".

"DELCO DON"
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Delco-Remy/AC-Delco Dist/Gen/Starter Etc Numbers Bud Tierney Antique Autos and Trucks 0 01-05-2015 05:09:03 PM
"DELCO DON" Delco 750 starter motor? Arthur Z Generators & Electric Motors General Discussion 1 05-05-2008 12:04:27 AM
More Delco help Ronnie Dykstra Generators & Electric Motors General Discussion 6 08-18-2005 12:07:30 PM
delco 850 Tim Delco and other Low Voltage DC Light Plants 2 11-04-2003 10:59:48 PM
Delco Help Keith Smigle Delco and other Low Voltage DC Light Plants 10 10-29-2002 12:03:01 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 09:39:03 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277