Antique Engines and Old Iron

[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® General Discussion > Antique Autos and Trucks
Forgot Password? Join Us!

Notices

Antique Autos and Trucks All about finding and fixing old car or truck engines and vintage vehicles.

Antique Autos and Trucks

Mack Bulldog


this thread has 53 replies and has been viewed 6041 times

Reply
 
Thread Tools Display Modes
  #21  
Old 11-18-2017, 06:33:32 PM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

As I understand it the logo cast into the engine & most castings is an M with an I in the middle of it, standing for "Mack International". Even after they changed the company name in 1922 to "Mack Trucks Inc." they retained the MI logo on the hood of the AC as well as on many castings.
Some castings, like the wheels on the 27, have the MACK script cast into them.
Attached Thumbnails
Click image for larger version

Name:	mack ac int. tr co..jpg
Views:	139
Size:	9.2 KB
ID:	296384   Click image for larger version

Name:	mack ac engine.jpg
Views:	171
Size:	58.9 KB
ID:	296385   Click image for larger version

Name:	mack ac logo.jpg
Views:	176
Size:	56.9 KB
ID:	296386  
Reply With Quote
The Following 6 Users Say Thank You to Jack Innes For This Post:
Sponsored Links
  #22  
Old 11-19-2017, 06:21:22 AM
Marcel P's Avatar
Marcel P Marcel P is offline
Subscriber
 
Join Date: Dec 2005
Location: Belgium
Posts: 730
Thanks: 3,650
Thanked 1,348 Times in 331 Posts
Default Re: Mack Bulldog

What a great truck! Very hard to find these days and in this condition. I cannot see it in the pictures but I suppose the tyres are vulcanised on steel rings that are pressed onto the wheels? If you can find some used forklift tyres it is fairly easy to bolt these on the rings once these are pressed off the wheels. Here are some pictures of the procedure. This was done with segments that came off a traction engine.

Regards
Marcel
Attached Thumbnails
Click image for larger version

Name:	P2280354.jpg
Views:	161
Size:	111.8 KB
ID:	296426   Click image for larger version

Name:	P3010370.jpg
Views:	154
Size:	147.2 KB
ID:	296427   Click image for larger version

Name:	DSCN1220.jpg
Views:	167
Size:	155.3 KB
ID:	296428   Click image for larger version

Name:	P3010367.jpg
Views:	158
Size:	152.9 KB
ID:	296429  
Reply With Quote
The Following 5 Users Say Thank You to Marcel P For This Post:
  #23  
Old 11-22-2017, 03:39:22 AM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

A bit of progress - I just found & ordered the correct Adlake tail light for the MACK AC. I have had the matching side lights for over 40 years.

https://www.lanternnet.com/Merchant2...72_568x675.jpg
Reply With Quote
The Following 2 Users Say Thank You to Jack Innes For This Post:
  #24  
Old 11-29-2017, 01:46:01 PM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

We had a mild day yesterday so I was able to do some work on the MACK. I made an adapter for the crank attachment & connected a gear reducer that I often use on new rebuilds or engines that have set for decades. The shaft turns at 30 rpm & helps free up stuck rings, valves, etc. So far the mag is working with the impulse acting & I have compression on 2 cylinders. There likely are sticky valves in the other 2. I let it roll over for about an hour & now that there is some compression the electric motor will stall unless I remove the plugs. The rig is obviously not strong enough to start the engine. I have adaptors for many smaller engines & it does start the smaller units. The MACK is 471 cid (5" bore, 6" stroke) so it is asking a lot to turn it under compression.
Attached Thumbnails
Click image for larger version

Name:	012.jpg
Views:	178
Size:	254.3 KB
ID:	297238   Click image for larger version

Name:	010.jpg
Views:	159
Size:	257.1 KB
ID:	297240  
Reply With Quote
The Following 7 Users Say Thank You to Jack Innes For This Post:
  #25  
Old 12-01-2017, 08:17:45 PM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

With more rotating & by turning the valves from below I now have compression on 3 cylinders. #4 exhaust valve is leaking badly & may need work. Does anyone have any suggestions on removing the valve plugs that have been in place for 50 years? The plugs have a straight thread & a copper gasket.

Jack
Attached Thumbnails
Click image for larger version

Name:	016.jpg
Views:	149
Size:	186.5 KB
ID:	297417  
Reply With Quote
The Following User Says Thank You to Jack Innes For This Post:
  #26  
Old 12-02-2017, 07:14:57 AM
Elden DuRand's Avatar
Elden DuRand Elden DuRand is offline
In Memory Of
 
Join Date: Nov 2004
Location: Port St. Joe, Florida, USA
Posts: 7,833
Thanks: 13,121
Thanked 7,897 Times in 2,967 Posts
Images: 11
Default Re: Mack Bulldog

Most times, you can get by with simply using a bar to loosen them. Sometimes, though, you need a special wrench and some careful "percussion therapy" to get them to break loose.
__________________

Take care - Elden
http://www.eldensengines.com
Reply With Quote
The Following User Says Thank You to Elden DuRand For This Post:
  #27  
Old 12-02-2017, 12:09:05 PM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

Thank you Elden, I have tried a bar & hammer but no luck. I am heading out to the shop to make a wrench.

Jack
Reply With Quote
  #28  
Old 12-02-2017, 01:54:00 PM
OTTO-Sawyer's Avatar
OTTO-Sawyer OTTO-Sawyer is offline
Subscriber
 
Join Date: Nov 2008
Location: Scioto Mills, Illinois USA
Posts: 8,927
Thanks: 19,536
Thanked 7,843 Times in 3,736 Posts
Default Re: Mack Bulldog

If you have an old broken or worn out socket laying around you could always weld a crossbar to it and use an impact wrench with the setting turned down lower.

Don't want to risk stripping the threads or breaking things but with the impact turned down lower it will still give it a light to moderate constant jarring motion in the right direction. Start low and slowly open the valve to where-ever you feel comfortable.

That couple with some good penetrating oil and or a light heating should get them out.

__________________
I just keep coming back again and again like the Evil Twin of a Bad Penny !
http://www.youtube.com/user/oldSawyer?feature=watch
Reply With Quote
The Following User Says Thank You to OTTO-Sawyer For This Post:
  #29  
Old 12-02-2017, 07:28:55 PM
squidtrap squidtrap is offline
Subscriber
 
Join Date: Nov 2012
Location: Forked River, New Jersey
Posts: 1,504
Thanks: 2,647
Thanked 788 Times in 512 Posts
Default Re: Mack Bulldog

i to find the impact on LOW will help alot with buildup. also i swear by ATF and acetone for penetrating oil. just need to shake real good, it likes to seperate.

also sometimes tighten first, then loosten.
Reply With Quote
The Following User Says Thank You to squidtrap For This Post:
  #30  
Old 12-02-2017, 09:09:25 PM
Jack Innes Jack Innes is offline
Subscriber
 
Join Date: Apr 2009
Location: Brooklin, Ontario, Canada
Posts: 440
Thanks: 254
Thanked 556 Times in 218 Posts
Default Re: Mack Bulldog

I spent the afternoon at the lathe & mill & am ready to try the impact tomorrow. The threads have been soaking in ATF/Acetone.

The 3/4 to 1/2" adaptor is a press fit in a square hole milled in the piece.
Attached Thumbnails
Click image for larger version

Name:	001.jpg
Views:	143
Size:	154.4 KB
ID:	297502   Click image for larger version

Name:	002.jpg
Views:	130
Size:	98.6 KB
ID:	297503  
Reply With Quote
The Following 4 Users Say Thank You to Jack Innes For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Mack Jr's SteamfanMN Antique Autos and Trucks 7 07-15-2014 09:41:05 PM
1930 Mack BL Corey Robinson Antique Autos and Trucks 1 09-05-2012 01:02:07 AM
1926 BullDog Mack Sky Antique Gas Engine Discussion 12 03-28-2010 02:45:47 PM
B 61 Mack James L Johnson Antique Autos and Trucks 3 08-03-2009 11:32:17 AM
Don Mack Linda Bogedain Old Engine Memorials 0 11-26-2005 09:41:49 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 04:57:41 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277