Oil Field Engines
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Oil Field Engines & Related Equipment
Forgot Password? Join Us!

Notices

Oil Field Engines & Related Equipment OFES members otherwise known as "Oafs". If you like "BIG OLD GREASY RUSTY OIL FIELD ENGINES, you're in the right place. Founded by Russell Farmer.

Oil Field Engines & Related Equipment

McEwen Bros half breed ignition -- need help


this thread has 2 replies and has been viewed 260 times

Reply
 
Thread Tools Display Modes
  #1  
Old 10-10-2018, 10:29:17 AM
farmacresinohio farmacresinohio is offline
Registered
 
Join Date: Aug 2018
Location: Waverly, Ohio / Aberdeen, Maryland
Posts: 1
Thanks: 2
Thanked 0 Times in 0 Posts
Default McEwen Bros half breed ignition -- need help

Need some advice. I am working on this McEwen Bros. half breed ---- running on a mag and seems to prematurely "double fire" (after 30 seconds of running near perfectly) and then stalls to a stop.

So I replumbed it completely to now include accumulator tank and Garretson KN demand regulator. Yes, the accumulator is between the gas grill regulator and demand regulator. Yes, I am using a 100 lb propane tank. Diamond valve is located after demand regulator (at intake). Question -- what is the cause of the additional ignition? I think it occurs BTDC, but unsure. Could a faulty intake valve result in this? Wrong spark plug? too rich? Currently, the mag ignites ATDC. Terribly confused. I notice the RPM's increase gradually before this "double fire" event happens. I can send pic and/or video if needed. Tony Skowronek, Southern Ohio.
Reply With Quote
Sponsored Links
  #2  
Old 10-10-2018, 01:04:35 PM
Bill Hazzard Bill Hazzard is offline
Registered-III
 
Join Date: Nov 2004
Location: Pennsylvania USA
Posts: 2,042
Thanks: 3,653
Thanked 4,544 Times in 1,137 Posts
Default Re: McEwen Bros half breed ignition -- need help

The ignition should take place before TDC, 5 or 10 degrees advanced should be fine for running slow.

What is happening with your engine is that as the engine speeds up the fuel mixture will get lean. When it does that, the burning fuel in the cylinder will burn so slowly that it will still be burning when the when the air and fuel is transferred from the scavenging side of the cylinder. That lights off the charge that is in the scavenging side of the cylinder which is what you are experiencing.

It is common for two cycle engines running on propane to experience this. Running the engine richer helps as does throttling the air down so it makes less power. A load on the engine helps as well.
Reply With Quote
The Following User Says Thank You to Bill Hazzard For This Post:
  #3  
Old 10-10-2018, 01:19:42 PM
Brian Lynch's Avatar
Brian Lynch Brian Lynch is offline
Subscriber
 
Join Date: Nov 2004
Location: Wellsville, New York, USA
Posts: 1,304
Thanks: 1,113
Thanked 1,151 Times in 453 Posts
Images: 23
Default Re: McEwen Bros half breed ignition -- need help

McEwen Bros. engines run better on a hot tube. That is how they were designed to run. They will run OK on a mag too. If you have the hot tube set up, try a 6" tube first. Work your way down to 4" to see how it reacts. Long tubes fire earlier, shorter tubes fire later. Where you heat them makes a difference too. Heating one at the bottom will fire sooner than one heated at the top end
__________________
"May your walk through life have no dogpiles in it" -Brian Lynch

Last edited by Brian Lynch; 10-10-2018 at 01:27:47 PM. Reason: more info.
Reply With Quote
The Following User Says Thank You to Brian Lynch For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Twin cylinder 4 cycle McEwen Bros., Wellsville, NY Brian Lynch Oil Field Engines & Related Equipment 2 10-18-2016 03:57:27 PM
Oil field related advert. item. McEwen Bros. Brian Lynch Oil Field Engines & Related Equipment 0 04-26-2012 09:59:38 PM
Innis / McEwen Bros. Half Breed bits & pieces Brian Lynch Oil Field Engines & Related Equipment 5 02-20-2011 09:17:08 AM
McEwen Bros. Steam Brian Lynch Steam Stationary Engines, Traction Engines, Steam Boats 4 02-20-2008 03:50:33 PM
McEwen bros. engines JIM WICKHAM Antique Engine Archives 0 02-24-2000 05:25:50 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 05:46:04 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277