Oil Field Engines
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Oil Field Engines & Related Equipment
Forgot Password? Join Us!

Notices

Oil Field Engines & Related Equipment OFES members otherwise known as "Oafs". If you like "BIG OLD GREASY RUSTY OIL FIELD ENGINES, you're in the right place. Founded by Russell Farmer.

Oil Field Engines & Related Equipment

A 4hp REID project by John Burns


this thread has 407 replies and has been viewed 119825 times

Reply
 
Thread Tools Display Modes
  #31  
Old 03-28-2008, 08:08:52 PM
Jordan's Avatar
Jordan Jordan is offline
Registered-III
 
Join Date: Aug 2005
Location: Delhi, Ontario, Canada
Posts: 1,706
Thanks: 1,648
Thanked 527 Times in 251 Posts
Default Re: 4hp REID crankshaft pic

looking good john. how long did it take you to turn the ends?

jordan
Reply With Quote
Sponsored Links
  #32  
Old 03-29-2008, 12:23:07 AM
John Burns John Burns is offline
Registered-III
 
Join Date: Oct 2005
Location: New Carlisle, Ohio, USA
Posts: 352
Thanks: 543
Thanked 1,738 Times in 225 Posts
Default Re: 4hp REID crankshaft pic

Takes 10 to 12 hrs per crank, 4140 mat'l

jb
Reply With Quote
The Following User Says Thank You to John Burns For This Post:
  #33  
Old 03-29-2008, 01:14:04 AM
Andrew Mackey Andrew Mackey is offline
Sponsor
 
Join Date: Nov 2004
Location: Rockaway, New Jersey USA
Posts: 13,390
Thanks: 1,884
Thanked 6,179 Times in 3,996 Posts
Exclamation Re: 4hp REID crankshaft pic

Looking good John!
Andrew
Reply With Quote
  #34  
Old 03-29-2008, 10:11:28 AM
Elden DuRand's Avatar
Elden DuRand Elden DuRand is offline
Subscriber
 
Join Date: Nov 2004
Location: Port St. Joe, Florida, USA
Posts: 7,830
Thanks: 13,099
Thanked 7,861 Times in 2,965 Posts
Images: 11
Default Re: 4hp REID crankshaft pic

John:

Where did you get the raw material (IF you will give away your secrets.). It looks like you had steel castings made especially for those crankshafts.

Those are gonna be nice shafts.

What do you do about heat treating or does that alloy remain stable after machining?

Take care - Elden
http://www.oldengine.org/members/durand/
Reply With Quote
  #35  
Old 03-29-2008, 02:18:18 PM
Mike Monnier's Avatar
Mike Monnier Mike Monnier is offline
Hoarder
 
Join Date: Nov 2004
Location: Casstown, Ohio, USA
Posts: 2,566
Thanks: 4,707
Thanked 3,102 Times in 953 Posts
Default Re: 4hp REID crankshaft pic

They appear to burnt out of plate to me Elden. You can see the distinctive pattern produced by a Blanchard grinder on the blank in the background. Looks beautiful John!
Reply With Quote
  #36  
Old 03-29-2008, 06:18:57 PM
John Burns John Burns is offline
Registered-III
 
Join Date: Oct 2005
Location: New Carlisle, Ohio, USA
Posts: 352
Thanks: 543
Thanked 1,738 Times in 225 Posts
Default Re: 4hp REID crankshaft pic

Eldan, they were billet cut (acetalyne torch) from large plates, annealed and ground. Then they were water jet cut to the blank dimentions.

jb
Reply With Quote
  #37  
Old 03-29-2008, 06:28:16 PM
John Burns John Burns is offline
Registered-III
 
Join Date: Oct 2005
Location: New Carlisle, Ohio, USA
Posts: 352
Thanks: 543
Thanked 1,738 Times in 225 Posts
Default Re: 4hp REID crankshaft pic

4140 has very strong tortional strength, it is a common alloy used for a variety of things. Any steel supplier can provide it for you.

jjb
Reply With Quote
  #38  
Old 03-29-2008, 07:59:08 PM
Elden DuRand's Avatar
Elden DuRand Elden DuRand is offline
Subscriber
 
Join Date: Nov 2004
Location: Port St. Joe, Florida, USA
Posts: 7,830
Thanks: 13,099
Thanked 7,861 Times in 2,965 Posts
Images: 11
Default Re: 4hp REID crankshaft pic

Quote:
Originally Posted by John Burns View Post
Eldan, they were billet cut (acetalyne torch) from large plates, annealed and ground. Then they were water jet cut to the blank dimentions.

jb
John:

That must have been some torch to cut that out! I can see how you do the mains but how do you turn the crankpin unless you have a really big lathe!

Take care - Elden
Reply With Quote
  #39  
Old 03-30-2008, 12:52:13 AM
John Burns John Burns is offline
Registered-III
 
Join Date: Oct 2005
Location: New Carlisle, Ohio, USA
Posts: 352
Thanks: 543
Thanked 1,738 Times in 225 Posts
Default Re: 4hp REID crankshaft pic

I have a local crankshaft grinding shop, all I have to do is give him accuratly milled square dimention on the throw and he will grind it!

jjb
Reply With Quote
  #40  
Old 04-07-2008, 01:14:46 AM
John Burns John Burns is offline
Registered-III
 
Join Date: Oct 2005
Location: New Carlisle, Ohio, USA
Posts: 352
Thanks: 543
Thanked 1,738 Times in 225 Posts
Default 4 hp REID crankshafts

More pic's, next stop crankshaft grinder!
jjb
Attached Thumbnails
Click image for larger version

Name:	john 119.jpg
Views:	618
Size:	27.3 KB
ID:	32026   Click image for larger version

Name:	john 120.jpg
Views:	750
Size:	26.9 KB
ID:	32027  
Reply With Quote
The Following User Says Thank You to John Burns For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Mike Burns BMiller Antique Gas Engine Discussion 4 09-03-2008 11:53:05 AM
What burns my bubble... KyleBlankenship Antique Gas Engine Discussion 19 04-03-2008 12:01:14 PM
Yet another Reid project saved Tom Schoolcraft Oil Field Engines & Related Equipment 7 07-20-2007 05:26:33 PM
Another 15hp Reid Project DONE Pix Tom Schoolcraft Antique Engine Archives 0 10-09-2004 12:04:48 AM
25 Hp Reid - New project! Chuck Martin Antique Engine Archives 10 07-07-2004 01:29:39 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 05:56:02 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2016 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277