Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® General Discussion > Smokstak Down Under
Forgot Password? Join Us!

Notices

Smokstak Down Under For Australia and New Zealand Smokstakers to meet, greet, yabber and yack.

Smokstak Down Under

About Time for an Engine Video


this thread has 237 replies and has been viewed 27694 times

Reply
 
Thread Tools Display Modes
  #221  
Old 08-03-2019, 05:57:46 PM
Scotty 2 Scotty 2 is offline
Registered
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,883
Thanks: 1,937
Thanked 2,246 Times in 1,177 Posts
Default Re: About Time for an Engine Video

Quote:
Originally Posted by Nathan Woodruff View Post
Also the blue contraption in the back ground is that a seed cleaner or thresher? Great to see working display
The corn sheller. Chuck the corn cobs in the top in the front and bag the corn on the side.
Sadly the drought has made it not possible to have enough corn to load the Junior up. Only about 1/2 a wheely bin of corn went though it in near a fortnight.

Cheers Scott

Reply With Quote
The Following 8 Users Say Thank You to Scotty 2 For This Post:
Sponsored Links
  #222  
Old 08-08-2019, 12:37:46 AM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

That is a very elaborate looking corn sheller. fantastic to see operating.
I am currently working on getting a dragsaw operating for our annual machinery rally coming up in October at Mil-lel South Australia. I like to try and get interesting working displays there are is ties in the well with the small agricultural show that runs in conjunction with us.
https://www.youtube.com/watch?v=_uZ5Xdg3kWo
Cheers, Nathan
Reply With Quote
The Following 2 Users Say Thank You to Nathan Woodruff For This Post:
  #223  
Old 08-13-2019, 12:40:37 AM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Here we go I got to test out the dragsaw on a nice log of blackwood. It seems to work very well apart from the old drive belt is disintegrating.
https://www.youtube.com/watch?v=fRiIL9U6cf0
Reply With Quote
The Following User Says Thank You to Nathan Woodruff For This Post:
  #224  
Old 08-13-2019, 02:36:53 AM
cobbadog cobbadog is offline
Registered
 
Join Date: Aug 2009
Location: Coopernook. N.S.W. Australia
Posts: 1,846
Thanks: 3,321
Thanked 821 Times in 553 Posts
Default Re: About Time for an Engine Video

What a beauty it is too Nathan, thanks for posting. I saw what looks like one of these model saws for sale at the Yesteryear Truck Show recently and it had an accessories on it that would be very helpful to all drag saws.
It had a pair of wheels mounted at the rear of the saw under the engine and facing at right angles to the saw blade. Don't know if it was original or a home made idea but the best we could think of is that they were there to move the saw along the log between each cut.
Reply With Quote
The Following User Says Thank You to cobbadog For This Post:
  #225  
Old 08-13-2019, 03:47:04 AM
Scotty 2 Scotty 2 is offline
Registered
 
Join Date: Mar 2011
Location: Warwick, Queensland, Australia
Posts: 2,883
Thanks: 1,937
Thanked 2,246 Times in 1,177 Posts
Default Re: About Time for an Engine Video

Hello Nathan
I had to laugh at the cow on the extreme right. She looked over after you put the belt on as if to think.....what the hell is he up to now?

Belts. They amase me sometimes. How they stay on when they're running all over the shop (as in the museum videos) has me beat.....but they do.

Cheers Scott
PS: your green grass is enough to make me cry.
Reply With Quote
The Following User Says Thank You to Scotty 2 For This Post:
  #226  
Old 08-13-2019, 07:06:46 AM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Quote:
Originally Posted by cobbadog View Post
What a beauty it is too Nathan, thanks for posting. I saw what looks like one of these model saws for sale at the Yesteryear Truck Show recently and it had an accessories on it that would be very helpful to all drag saws.
It had a pair of wheels mounted at the rear of the saw under the engine and facing at right angles to the saw blade. Don't know if it was original or a home made idea but the best we could think of is that they were there to move the saw along the log between each cut.
Yes I have seen a couple where you take the wheels off and mount them at right angles to the saw blade. Great idea makes it easier to slide it along the log.

Hi Scotty I was eyeing the cow off for a new bit of leather to make a new belt out of. You are right with a good old flat belt it is amazing how they can stay on and yet the day you try to line it all up perfectly you can never get them to stay on. I have learnt a few tricks and it gets easier the longer the length of the belt.
We are lucky in our part of the world as a dry year usually for us is having the grass die off in the middle of summer although this year the grass has only come back in the last month
Reply With Quote
The Following User Says Thank You to Nathan Woodruff For This Post:
  #227  
Old 08-17-2019, 04:43:35 AM
Patrick M Livingstone's Avatar
Patrick M Livingstone Patrick M Livingstone is online now
Registered
 
Join Date: Nov 2004
Location: Sydney, Australia
Posts: 1,926
Thanks: 5,078
Thanked 4,982 Times in 1,067 Posts
Default Re: About Time for an Engine Video

I fired up this old girl today. I forget what I great runner it is until I fire it up again
Reply With Quote
The Following 4 Users Say Thank You to Patrick M Livingstone For This Post:
  #228  
Old 08-17-2019, 05:22:36 AM
AussieIron AussieIron is online now
Subscriber
 
Join Date: Mar 2012
Location: Ararat, Victoria, Australia
Posts: 457
Thanks: 388
Thanked 471 Times in 196 Posts
Default Re: About Time for an Engine Video

Nathan, I believe that saw was built by Faneco and Wholers? If it was, it was built 50 yards from where I'm sitting. The factory was one block away from my street. Not a trace left now. I have seen an early engine built by them in Ararat. Mainly all T model parts, had a wooden top crankcase cover from memory. I have seen a four HP Sundial on one of their saws. Don't know if original or not. Ararat also made a vertical steam engine, but I don't think a Faneco.
18 miles north, at Stawell, Kayes made a vertical engine,2 stroke I think. They made a fair few engines, scarce now. Their factory was somewhere around where the Trotting Track at Stawell is now. I knew where a set of flywheels and crank were once, you could tell it was a Kaye as they had an exceptionally wide crankshaft. Good to see the saw preserved and running. Cheers - Neil.
Reply With Quote
The Following User Says Thank You to AussieIron For This Post:
  #229  
Old 08-18-2019, 02:23:58 AM
isandian isandian is offline
Registered
 
Join Date: Nov 2010
Location: Sydney, NSW, Australia
Posts: 369
Thanks: 426
Thanked 352 Times in 172 Posts
Default Re: About Time for an Engine Video

There was a Kaye at Lake Goldsmith on the couple of occasions I have been there. I have seen a couple of others in private hands, but certainly a very rare and interesting engine. Ian
Reply With Quote
The Following 3 Users Say Thank You to isandian For This Post:
  #230  
Old 08-19-2019, 09:12:27 PM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Ronnie N type just got running. Sorry for the dark video when I get time will get a better video. There is something a little different that makes this N type stand out from the crowd.
https://www.youtube.com/watch?v=BcDuHj1-2og
Reply With Quote
The Following 4 Users Say Thank You to Nathan Woodruff For This Post:
  #231  
Old 09-09-2019, 01:26:55 AM
karragullengine karragullengine is offline
Registered
 
Join Date: Mar 2014
Location: Karragullen Western Australia
Posts: 295
Thanks: 310
Thanked 213 Times in 123 Posts
Default Re: About Time for an Engine Video

Two of my daughters demonstrating out little howard 2000 tractor with an offset rotary hoe i recently purchased and got back to running condition. Great little unit.
https://youtu.be/yqpbb86kZl8
Reply With Quote
The Following 5 Users Say Thank You to karragullengine For This Post:
  #232  
Old 09-13-2019, 08:37:10 PM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Helped a mate seal up his Marshall portable for an upcoming rally and thought we might belt it up to a rock crusher for a bit of load to check it out.
https://www.youtube.com/watch?v=S3J4O9boSkk
Reply With Quote
The Following 8 Users Say Thank You to Nathan Woodruff For This Post:
  #233  
Old 09-23-2019, 09:55:00 PM
Patrick M Livingstone's Avatar
Patrick M Livingstone Patrick M Livingstone is online now
Registered
 
Join Date: Nov 2004
Location: Sydney, Australia
Posts: 1,926
Thanks: 5,078
Thanked 4,982 Times in 1,067 Posts
Default Re: About Time for an Engine Video

Some video from the 2019 Clarendon Classic
Reply With Quote
The Following 11 Users Say Thank You to Patrick M Livingstone For This Post:
  #234  
Old 09-24-2019, 05:46:12 AM
AussieIron AussieIron is online now
Subscriber
 
Join Date: Mar 2012
Location: Ararat, Victoria, Australia
Posts: 457
Thanks: 388
Thanked 471 Times in 196 Posts
Default Re: About Time for an Engine Video

Great video as usual. Some lovely engines there, thanks. Cheers-Neil.
Reply With Quote
The Following 2 Users Say Thank You to AussieIron For This Post:
  #235  
Old 09-24-2019, 06:47:05 AM
asw20 asw20 is offline
Registered
 
Join Date: Sep 2018
Location: Ipswich, Queensland, Australia
Posts: 32
Thanks: 15
Thanked 15 Times in 12 Posts
Default Re: About Time for an Engine Video

It was my privilege to see that Robson engine at the owner's property today. An impressive bit of gear.

Thanks for the video.

Jarrod.
Reply With Quote
The Following User Says Thank You to asw20 For This Post:
  #236  
Old 10-04-2019, 01:58:18 AM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Getting a few steam engines sealed up and some other machinery ready for the next Lake Goldsmith steam rally
https://www.youtube.com/watch?v=tqw2...ature=youtu.be
Reply With Quote
The Following 5 Users Say Thank You to Nathan Woodruff For This Post:
  #237  
Old 10-08-2019, 02:33:26 AM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

Engines running at recent heritage day at Millicent Museum. Only had a couple out as the weather was threatening to pour rain so made sure it was easy to get them back in the shed incase of heavy rain.
https://www.youtube.com/watch?v=OVzb...ature=youtu.be
Reply With Quote
The Following 3 Users Say Thank You to Nathan Woodruff For This Post:
  #238  
Old 10-15-2019, 11:14:19 PM
Nathan Woodruff Nathan Woodruff is offline
Registered
 
Join Date: Nov 2013
Location: Moorak, South Australia, Australia
Posts: 400
Thanks: 506
Thanked 568 Times in 195 Posts
Default Re: About Time for an Engine Video

The stationary engine and machinery section of the Mil-lel steam and machinery association rally that was on last weekend. unfortunately I did not get a lot of video and pictures from the rally as I was busy with my own exhibits and helping out some others.
https://www.youtube.com/watch?v=a_e1...ature=youtu.be
Reply With Quote
The Following 3 Users Say Thank You to Nathan Woodruff For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Old Time Video Full of Machinery - Be warned, no gas engines! MFaris Hit & Miss Gas Engine Discussion 1 01-08-2018 08:34:59 AM
Sawing down a big tree one piece at a time. Interesting video OTTO-Sawyer YouTube Old Iron Videos 10 03-05-2013 03:36:24 PM
Blast back into time 1904 in the Westinhouse Engine Factory - Video Wayne Grenning Hit & Miss Gas Engine Discussion 13 11-13-2012 07:28:51 AM
Awesome video - Triumph Spitfire Engine Rebuild Time-Lapse Video KD5BYB Hit & Miss Gas Engine Discussion 6 07-01-2012 12:07:33 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 06:34:19 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277